ENDA EDP 141 Manual Download Page 2

     4 digits  7 segment yellow LED display

  ( 2 ),( 3 ),( 4 ) Keypad

  ( 1 ) Digital display

 2/3

EDP141

-E-05

2

1

184-253V AC 
50/60Hz 3VA

230V AC 
Besleme

Anahtar

Fuse

F 100 mA 250V AC

 9.1mm       

      Micro switch

 Note   1) Panel thickness should  

be maximum 7mm
2) If there is no 60mm free 
space at back side of the 
device, it would be difficult 
to remove it from the panel.

3

4

m

m

70mm

8mm

85mm

71mm

2

9

m

m

Flush mounting 

clamp

Rubber

Panel

2

1

SN

: X

XX

XX

XX

XX

1

2

3

4

5

6

7

8

9

10

11

12

EN

DA

 

IN

DU

ST

RIA

L E

LE

CT

RO

NIC

S

2

3

0

V

 A

C

 +

1

0

%

 -

2

0

%

5

0

/6

0

H

z

   

3

V

A

EI141

SET

ENDA

EDP141

DIGITAL POTENTIOMETER

   

 E

DP

14

1 D

IG

IT

AL

 P

OT

EN

TIO

ME

TE

R

0

-1

0

V

 D

C

 O

U

P

U

T

G

N

D

SN: XXXXXXXXX

1

2

3

4

5

6

7

8

9 10 11 12

    EDP141 DIGITAL POTENTIOMETER

ENDA

 

INDUSTRIAL ELECTRONICS

2

3

0

V

 A

C

 +

1

0

%

 -

2

0

%

5

0

/6

0

H

z

  

 7

V

A

0

-1

0

V

 D

C

 O

U

P

U

T

G

N

D

SN: XXXXXXXXX

1

2

3

4

5

6

7

8

9 10 11 12

ENDA

 

INDUSTRIAL ELECTRONICS

2

4

V

 D

C

 

1

0

%

7

V

A

±

G

N

D

EDP141-24DC DIGITAL POTENTIOMETER

+

 

SN: XXXXXXXXX

1

2

3

4

5

6

7

8

9 10 11 12

 EI141-24AC DIGITAL POTENTIOMETER 

ENDA

 

INDUSTRIAL ELECTRONICS

2

4

V

 A

C

 +

1

0

%

 -

2

0

%

5

0

/6

0

H

z

  

 7

V

A

G

N

D

0

-1

0

V

 D

C

 O

U

P

U

T

0

-1

0

V

 D

C

 O

U

P

U

T

1) Adjusted potentiometer value is seen in run mode
    Parameter name, value or its unit in programming mode.

3) Decrement key during run mode.
    Decrement or parameter selection key during programming mode.

2) Increment key during run mode.
    Increment or parameter selection key during programming mode.

4) Used for selecting run or programming modes and for adjusting parameters. 

 

 -  

Push up the flush-mounting 

     clamp in direction 

1

 as    

     

shown in the figure above.

 

 -  

Then, pull out the clamp in  

     

direction 

2.

 

For removing mounting clamps:

DIMENSIONS

Panel cut-out

Flush mounting 

clamp

TERMS

ENDA EDP 141 is intended for installation in control panels. Make sure that the device is used only for intended purpose. 

During an installation, all of the cables that are connected to the device must be free of energy. The device 

must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. All 
input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be 
close to the power cables or components. 

The shielding must be 

grounded on the instrument side. 

The installation and electrical connections must be carried on by a qualified staff and must be 

according to the relevant locally applicable regulations.  

CONNECTION DIAGRAM

Neutral

Line

SUPPLY :

NOTE :

Fuse should
be connected

Cable size: 1,5mm²

Holding screw
0.4-0.5Nm 

Equipment is protected throughout
by DOUBLE INSULATION.

Note: 1) Mains supply cords shall meet the requirements of  IEC 60227 or IEC 60245. 

2) In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it 

should 

 

be easily accessible by the operator.

  

         Character height

EI141

SET

ENDA

EDP141

DIGITAL POTENTIOMETER

Reviews: