Encore ENHWI-N2 User Manual Download Page 62

Page: 62 / 62

ELN/[email protected]

and your password, where username is your own username (some Earthlink

users may not need the

ELN/

in front of username).

For SBC Global users, enter

[email protected]

For Ameritech users, enter

[email protected]

For BellSouth users, enter

[email protected]

.**

For most other ISPs, enter

username

Step 7

Idle Time Out

should be set to zero. Set

MTU

to 1492, unless specified by your ISP.

Note:

If you experience problems accessing certain websites and/or email issues, please set the MTU to a lower

number such as 1472, 1452, etc. Contact your ISP for more information and the proper MTU setting for your
connection.

Step 8

Click

Apply

. When prompted, click

Continue

. Once the screen refreshes, unplug the power to the

router.

Step 9

Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem has established a link to

your ISP, plug the power back into the router. Wait about 30 seconds and log back into the router.

Step 10

Click on the

Status

tab in the web configuration where you can view the device info. Under

WAN

click

DHCP Release

, then click

Back

then click

DHCP Renew

, and then click

Back

. You should now see that

the device info will show an IP address, verifying that the device has connected to a server and has been
assigned an IP address.

Summary of Contents for ENHWI-N2































































Search results

Summary of Contents for ENHWI-N2

Reviews:

Related manuals for ENHWI-N2

Brands by name

Popular brands

Encore ENHWI-N2, User Manual

Search results

Summary of Contents for ENHWI-N2

Reviews:

Related manuals for ENHWI-N2

Brands by name

Popular brands