background image

 
IRB-MON Operating Instructions 

 

11 

Document no.

  10280104 

 

 

 

Troubleshooting  

 

Symptom 

Possible cause 

Solution 

Does not detect obstruction 
of beam 

Sensitivity too high 
 
 
Signal is reflecting off another 
surface 

Adjust SENSITIVITY pot 
counter-clockwise 
 
Check area for highly reflective 
surfaces 

Green LED flashes 
continuously (indicating an 
obstruction when an 
obstruction is not present) 

Sensitivity too low 
 
 
Transmitter does not have 
power 
 
 
Receiver does not “see” 
transmitter 

Adjust SENSITIVITY pot 
clockwise 
 
Check power source for 
transmitter 
 
Make sure transmitter and 
receiver have line of sight 
alignment 

Receiver activates but does 
not transmit signal to 
operator 

Faulty connection between 
receiver and operator control 
input 

Verify all wires and terminal 
connections  

Receiver green LED off (1) 

Transmitter too close to 
receiver 

Adjust SENSITIVITY pot 
counter-clockwise 
 
Increase distance between 
transmitter and receiver 

 

(1)

 

When transmitter is too close to the receiver the green LED will turn off, this prevents 
mounting the photo eyes in close proximity. 

 

 

 

Summary of Contents for IRB-MON















Reviews: