EMX Industries, Inc. IRB-325 Operating Instructions Manual Download Page 3

IRB-325 Instructions 

 

Document no.     

REV 1.0    

Date 10/25/2007 

 

 

Product Overview 

 

The IRB-325 conforms to the UL325 standard when used with the powder coated steel 
hoods. Registration reference number 9901994.  The IRB-325 photocell is used as an 
external entrapment protection device type B1 non-contact sensor for use with automatic gate 
and door openers. 

 

The IRB-325 transmitter and receiver have a line of site range of up to 65 feet. The IRB-325 
operates on 12 VDC to 24 VAC and draw 150 mA maximum. 

 

The IRB-325 receiver is activated whenever anything interrupts the beam from the 
transmitter, triggering the relay output to change state and send a signal to the operator that 
there has been an interruption. 

 

Technical Specifications 

 

 

 

Controls, Indicators and Connections 

 

 

 

 

Transmitter   

 

 

     Receiver

 

 

 

 

 
 

 

 
 
 

 
 

 
 

 

 
 

 
 

The IRB-325 is an external entrapment device Type B1 non-contact sensor for use 
with automatic gate operators. If the IRB-325 is used as the primary entrapment 
protection device it must be monitored for presence and fault condition. 

 
 

 

Power Supply 

12 Volts Dc to 24Volts AC 

 Power Supply Tolerance 

+/- 20% 

 Current Draw 

150 mA maximum 

 Housing Material 

UL and CSA Type 4, 4X, 3, 3R, 12, 13 rating  and powder coat steel hood 

 Relay Type 

Type C       Rating 1A @ 30 VDC 

 Temperature Range 

-40

o

 F to 170

o

 F 

 Connector  

Screw terminal isolated contact  (2) transmitter  (5) receiver 

 Power Indicator 

Green LED 

 Detect Indicator 

Red LED 

 Dimensions 

H=5.03 in, W=3.06 in, D=3.02 in 

 Range 

6 feet to 65 feet line of sight 

Power 

LED 

 

Green SMT glows when power is applied 

Power 

LED 

 

Green SMT glows when power is applied 

Connections 

Screw terminal 

 

2 position for power source 

Connections 

Screw terminal 

 

5 position for power and controls 

Detect 

LED 

 

(2) Red SMT LEDs glow on detection 

Summary of Contents for IRB-325









Reviews: