EMS5 MLS-202-C User Manual Download Page 2

 

 

 

-- 

 

I
 

COPYRIGHT 

 

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, 

or transmitted in any form or by any means, whether electronic, mechanical, photo copying, 
recording or otherwise, without the prior written permission of the publisher. 

 
       

 

FCC WARNING 

 

This equipment has been tested and found to comply with the limits for a class B device, pursuant 
to  part  15  of  FCC  rules.  These  limits  are  designed  to  provide  reasonable  protection  against 
harmful interference in a commercial installation. This equipment generates, uses and can radiate 
radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the  instructions, may 
cause  harmful  interference to  radio  communication.  Operation  of  this  equipment  in  a  residential 
area is likely to cause harmful interference, in which case, the user will be required to correct the 
interference at the 

user’s own expense. 

 

 

CE WARNING 

 

This is a Class B product. In a domestic environment, this product may cause radio interference 
in which case the user may be required to take adequate measures. 

 

Take special care to read and understand all the content in the warning boxes: 

Warning 

 

 

 

 

 

 
 

 
 

Summary of Contents for MLS-202-C












Reviews: