background image

26284-3-0813

Page 8

Check all local codes for requirements, especially for the size and 

type of gas supply line required.

NOTICE

:

 Never use plastic pipe. Check to confirm whether your 

local codes allow copper tubing or galvanized.

NOTICE

Since some municipalities have additional local codes, it is 

always best to consult your local authority and installation code.

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.
In the state of Massachusetts the gas cock must be a T handle 

type.
A manual main gas cock should be located in the vicinity of the unit. 

Where none exists, or where its size or location is not adequate, 

contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant 

to the action of liquefied petroleum gases. The gas lines must be 

checked for leaks by the installer. This should be done with a soap 

solution watching for bubbles on all exposed connections, and if 

unexposed, a pressure test should be made. 

Never use an exposed flame to check for leaks. Appliance must 

be disconnected from piping at inlet of control valve  and pipe 

capped or plugged for pressure test. Never pressure test with 

appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas 

line upstream of the gas control to aid in servicing. It is required by 

the National Fuel Gas Code that a drip line be installed near the gas 

inlet. This should consist of a vertical length of pipe tee connected 

into the gas line that is capped on the bottom in which condensation 

and foreign particles may collect. 
 The use of the following gas connectors is recommended:
—  ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing 

and Fittings

—  ANS Z21.45 Assembled Flexible Appliance Connectors of Other 

Than All-Metal Construction

The above connectors may be used if acceptable by the authority 

having jurisdiction. The state of Massachusetts requires that a flexible 

appliance connector cannot exceed three feet in length.

Figure 4

Pressure Testing of the Gas supply system

1.  To check the inlet pressure to the gas valve, a 1/8" (3.175mm) 

N.P.T. plugged tapping, accessible for test gauge connection, must 

be placed immediately upstream of the gas supply connection 

to the appliance.

2.    The appliance and its individual shutoff valve must be disconnected 

from the gas supply piping system during any pressure testing of 

that system at test pressures in excess of 1/2 psig (3.5 kPa).

3.    The appliance must be isolated from the gas supply piping system 

by closing its individual manual shutoff valve during any pressure 

testing of the gas supply piping system at test pressures equal 

to or less than 1/2 psig (3.5 kPa).

Attention! 

If one of the procedures results in pressures in excess 

of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will 

result in a hazardous condition.

Checking Manifold Pressure 

VsR 

Natural gas models will have a manifold pressure of approxi-

mately 3.5" w.c. (.871kPa) at the pressure regulator outlet with the 

inlet pressure to the pressure regulator from a minimum of 4.5" w.c. 

(1.120kPa) for the purpose of input adjustment to a maximum of 

10.5" w.c. (2.615kPa). 

VsM

 Natural gas models will have a mani-

fold pressure of approximately 4.5" w.c. (1.12kPa)  at the pressure 

regulator outlet with the inlet pressure to the pressure regulator 

from a minimum of 7.0" w.c. (1.74kPa) for the purpose of input 

adjustment to a maximum of 10.5" w.c. (2.615kPa). 

VsR and VsM

 

Propane gas models will have a manifold pressure approximately 

10.0" w.c. (2.49kPa) at the pressure regulator outlet with the inlet 

pressure to the pressure regulator from a minimum of 11.0" w.c. 

(2.739kPa) for the purpose of input adjustment to a maximum of 

13.0" w.c. (3.237kPa). 

VsM

NOTICE

A test gage connection is located downstream of the gas 

appliance pressure regulator for measuring gas pressure. The con-

nection is a 1/8 inch 3mm) N.P.T. plugged tapping.

VsR

NOTICE

The gas control is equipped with a captured screw type 

pressure test point, therefore it is not necessary to provide a 1/8" 

test point up stream of the control.

GAs suPPly

Recommended Gas Pipe diameter

Pipe Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L 

Outside Diameter

Nat.

L.P.

Nat.

L.P.

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5mm

1/2”

12.7mm

3/8”

9.5mm

10-40 feet

4-12 meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

1/2”

12.7mm

40-100 feet

13-30 meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150 feet

31-46 meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2mm

3/4”

19mm

Summary of Contents for VSM-18-1





















Reviews: