background image

Page 12

R-5210

PLEASE NOTE:  When ordering parts, it is very important that  part number and description of part coincide.

1

10812

CASING SIDE ASSEMBLY - LEFT

2

SR-180

CASING BACK

3

R-2313

PIEZO IGNITOR

4

SR-008

CASING SIDE ASSEMBLY - RIGHT

5

SR-113

VALVE BRACKET

6

R-2351

GAS VALVE -SIT

7

R-2406

MALE CONNECTOR 1/4 TUBE X 3/8
NPT

8

R-2423

MALE CONNECTOR 5/16 TUBE X 3/8
NPT (2 REQUIRED)

9

SR-152

TUBING - GAS VALVE TO BURNER

10

SR-214

TUBING - INLET REGULATOR TO GAS
VALVE

11

10753

INLET REGULATOR BRACKET

12

R-5097

INLET REGULATOR - NAT

12

R-5098

INLET REGULATOR - LPG

13

SR-158

TUBING - GAS VALVE TO PILOT

14

R-2314

ORIFICE HOLDER

INDEX

   PART

NUMBER

   NUMBER

DESCRIPTION

 USE ONLY MANUFACTURED REPLACEMENT PARTS.  USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

1. Spark electrode does not produce spark.

a. Spark electrode broken - replace.
b. Ignitor wire may not be attached to spark electrode - attach.
c. Ignitor wire damaged - replace.
d. Piezo ignitor defective - replace.

2. Spark electrode produces spark but pilot does not light.

a. No gas to heater - turn on gas.
b. PILOT position not properly aligned - turn gas control knob

to PILOT position and depress.

c. Pilot is blocked from spider web or dirt - clean pilot, see Page 9.

3. Pilot flame does not stay "ON" when control knob is released.

a. Control knob in PILOT position not completely depressed or

held in long enough.

b. INTERLOCK latching device is operative - see "Lighting

Instructions," Page 11, Step  9.

c. Thermocouple not tightened into gas control - tighten ther-

mocouple.

d. Pilot flame not surrounding thermocouple - clean pilot, see

Page 9.

e. Inlet gas pressure too low, contact gas supplier.
f. Thermocouple defective - replace.
g. Gas control defective - replace.

4. Main burner does not ignite.

a. Main burner orifice is blocked - clean, see "Main Burner

Flame," Page 9.  Attention:  The number stamped on the main
burner orifice is a millimeter diameter.

b. Inlet gas pressure too low, contact gas supplier.

5. Heater keeps shutting "OFF" during normal operation.

a. Pilot is blocked - clean pilot, see Page 9.
b. Inlet gas pressure too low, contact gas supplier

TROUBLESHOOTING INFORMATION FOR QUALIFIED SERVICE PERSON

SYMPTOMS - POSSIBLE CAUSES AND CORRECTIONS

SR-10T

INDEX

   PART

NUMBER

   NUMBER

DESCRIPTION

15

R-2317

MAIN BURNER ORIFICE - NAT

15

R-2476

MAIN BURNER ORIFICE - LPG

16

R-2331

BURNER

17

R-5002

THERMOCOUPLE LEAD

18

R-5000

PILOT/THERMOCOUPLE ASSEMBLY
(LPG ONLY)) (INCLUDES ITEM #17)

18

R-5006

PILOT/THERMOCOUPLE ASSEMBLY
(NAT ONLY)) (INCLUDES ITEM #17)

19

SR-179

PILOT BRACKET

20

SR-153

ORIFICE SHIELD

21

R-2305

CHROME GRILL

22

SR-134

CASING LOUVER (2 REQUIRED)

23

SR-129

REFLECTOR ASSEMBLY

24

SR-135

HEAT SHIELD

25

R-1992

BULB CLIP

26

SR-154

OPTIONAL SRS-10 FLOOR STAND
KIT

NOT SHOWN

R-5008

IGNITOR WIRE

NOT SHOWN

 SR-216

HARDWARE PACKAGE

Empire Comfort Systems, Inc.  Nine Eighteen Freeburg Ave.   Belleville, IL  62222-0529

How To Order Repair Parts

...

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor.
Parts can be shipped directly to the service person/dealer.

All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then
determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give
all this information . . .

Unvented Heater Model Number

Part Description

Unvented Heater Serial Number

Type of Gas (Propane or Natural)

Part Number

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipments contingent upon strikes, fires and all causes beyond our control.

Summary of Contents for SR-10T-2



















Reviews: