background image

31449-4-1113

Page 51

A.  BEFORE LIGHTING smell all around the appliance area 

for gas. Be sure to smell next to the floor because some 

gas is heavier than air and will settle on the floor.

 

WHAT TO DO IF YOU SMELL GAS

 •  Do not try to light any appliance

 •  Do not touch any electrical switch

 •  Do not use any phone in your building.

 •  Immediately call your gas supplier from a neighbor's  

phone.

 •  Follow the gas supplier's instructions.

 •  If you can not reach your gas supplier, call the fire 

 

department.

B.  Use only the wall switch or remote control switch to 

turn the gas control on/off. Any attempted repairs or 

adjustments should be performed by a qualified service 

technician. Applying force or attempted repair may result 

in a fire or explosion.

C.  Do not use this appliance if any part has been under 

water. Immediately call a qualified service technician 

to inspect the appliance and to replace any part of the 

control system and any gas control which has been 

under water.

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY 

RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

1.  STOP! Read the safety information above.
2.  Turn off all electric power to the appliance.
3.  Open bottom louver assembly, or open the valve access 

door.

4.  Turn gas line valve to "OFF."
5.  Close bottom louver assembly, or close valve access 

door.

1.  STOP! Read the safety information above.
2.  Set the thermostat, if used, to the lowest setting.
3.  Turn off all electric power to the appliance.
4.  This appliance is equipped with an ignition device that 

automatically lights the burner. Do not try to light the 

burner by hand.

5.  Open bottom louver assembly.
6.  Turn gas line valve to “ON.”

7.  Wait five (5) minutes to clear out any gas. Then smell 

for gas, including near the floor. If you smell gas, STOP! 

Follow “A” in the safety information above. If you do not 

smell gas, go to the next step.

8.  Close bottom louver assembly.

9.  Turn on all electric power to the appliance.
10. Set thermostat to desired setting (if available).
11.  If the appliance will not operate, follow the instructions 

“TO TURN OFF GAS TO APPLIANCE,” and call your 

service technician or gas supplier.

ON

OFF

DIRECT IGNITION LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

Summary of Contents for DVX36FP31L-4

















































































Reviews: