Empire BF-10-1 Installation Instructions And Owner'S Manual Download Page 9

R-4973

Page 9

1. Spark electrode does not produce spark.

a. Spark electrode broken - replace.
b. Ignitor wire may not be attached to spark electrode - attach.
c. Ignitor wire damaged - replace.
d. Piezo ignitor defective - replace.

2. Spark electrode produces spark but pilot does not light.

a. No gas to heater - turn on gas.
b. PILOT position not properly aligned - turn gas control knob

to PILOT position and depress.

c. Pilot is blocked from spider web or dirt - clean pilot, see Page 7.

3. Pilot flame does not stay "ON" when control knob is released.

a. Control knob in PILOT position not completely depressed or

held in long enough.

b. INTERLOCK latching device is operative - see "Lighting

Instructions," Page 8, Step  9.

c. Thermocouple lead not tightened into gas control - tighten

thermocouple lead.

d. Pilot flame not surrounding thermocouple - clean pilot, see

Page 7.

e. Inlet gas pressure too low, contact gas supplier.
f. Thermocouple defective - replace pilot.
g. Gas control defective - replace.

4. Main burner does not ignite.

a. Main burner orifice is blocked - clean, see "Proper Main

Burner Flame," Page 6.

b. Inlet gas pressure too low, contact gas supplier.

5. Heater keeps shutting "OFF" during normal operation.

a. Pilot is blocked - clean pilot, see Page 7.
b. Inlet gas pressure too low, contact gas supplier

TROUBLESHOOTING INFORMATION FOR QUALIFIED SERVICE PERSON

SYMPTOMS - POSSIBLE CAUSES AND CORRECTIONS

INDEX

   PART

  NO.

     NO.

DESCRIPTION

INDEX

   PART

  NO.

     NO.

DESCRIPTION

1

10812

CASING SIDE ASSEMBLY - LEFT
(BF-10)

1

10811

CASING SIDE ASSEMBLY - LEFT
(BF-20, BF-30)

2

SR-090

CASING BACK ASSEMBLY (BF-10
BF-20)

2

SR-041

CASING BACK ASSEMBLY(BF-30)

3

R-2313

PIEZO IGNITOR

4

R-5008

IGNITOR WIRE

5

SR-008

CASING SIDE ASSEMBLY - RIGHT

6

R-1992

BULB CLIP

7

SR-076

CASING LOUVER-TOP (BF-10 BF-20)

7

SR-017

CASING LOUVER-TOP (BF-30)

8

SR-077

HEAT SHIELD (BF-10 BF-20)

8

SR-018

HEAT SHIELD (BF-30)

9

SR-075

REFLECTOR SHIELD REAR
(BF-10 BF-20)

9

SR-016

REFLECTOR SHIELD REAR (BF-30)

10

10420

REAR SHIELD (BF-10 BF-20)

10

10478

REAR SHIELD (BF-30)

11

10417

REFLECTOR ASSEMBLY
(BF-10 BF-20)

11

10475

REFLECTOR ASSEMBLY (BF-30)

12

10467

CASING LOUVER-BOTTOM
ASSEMBLY (BF-10 BF-20)

12

10479

CASING LOUVER-BOTTOM
ASSEMBLY (BF-30)

13

R-4979

CHROME GRILL (BF-10 BF-20)

13

R-4980

CHROME GRILL (BF-30)

14

R-4993

GLASS (BF-10 BF-20)

14

R-4994

GLASS (BF-30)

15

R-5100

INLET REGULATOR - NAT

15

R-5098

INLET REGULATOR - LPG

16

10753

INLET REGULATOR BRACKET

17

10462

TUBING - GAS VALVE TO BURNER
(BF-10 BF-20)

17

10484

TUBING - GAS VALVE TO BURNER
(BF-30)

18

SR-214

TUBING - INLET REGULATOR TO
GAS VALVE

19

R-2423

MALE CONNECTOR 5/16 TUBE X 3/8
NPT (2 REQUIRED)

20

R-2351

GAS VALVE (BF-10 NAT AND LPG)

20

10537

GAS VALVE (BF-20 NAT AND BF-30
NAT)

20

10538

GAS VALVE (BF-20 LPG AND BF-30
LPG)

PLEASE NOTE:  When ordering parts, it is very important that  part number and description of part coincide.

  USE ONLY MANUFACTURER'S REPLACEMENT PARTS.  USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

21

SR-113

VALVE BRACKET

22

10460

BURNER BRACKET - LEFT

23

10422

BURNER (BF-10  BF-20)

23

10480

BURNER (BF-30)

24

10424

AIR SHUTTER (BF-10 ONLY)

25

10461

BURNER BRACKET - RIGHT

26

P-214

MAIN BURNER ORIFICE (BF-10 NAT)

26

P-193

MAIN BURNER ORIFICE (BF-10 LPG)

26

P-252

MAIN BURNER ORIFICE (BF-20 NAT)

26

742286

MAIN BURNER ORIFICE (BF-20 LPG)

26

P-211

MAIN BURNER ORIFICE (BF-30 NAT)

26

P-185

MAIN BURNER ORIFICE (BF-30 LPG)

27

P-212

ORIFICE HOLDER

28

10424

AIR SHUTTER (BF-10 NAT & LPG)
(BF-20 & BF-30 LPG ONLY)

29

10539

TUBING - GAS VALVE TO PILOT
(BF-10 BF-20)

29

10540

TUBING - GAS VALVE TO PILOT
(BF-30)

30

R-5007

PILOT ASSEMBLY (NAT ONLY)
(INCLUDES 31)

30

R-5001

PILOT ASSEMBLY (LPG ONLY)
(INCLUDES 31)

31

R-5003

THERMOCOUPLE LEAD

32

SR-120

OPTIONAL SRS-18 FLOOR STAND
KIT (BF-10 BF-20)

32

SR-115

OPTIONAL SRS-30 FLOOR STAND
KIT (BF-30)

33

SR-122

OPTIONAL SRB-18T BLOWER KIT
(BF-10 BF-20) (INCLUDES 34
THROUGH 41)

33

SR-116

OPTIONAL SRB-30T BLOWER KIT
(BF-30) (INCLUDES 34 THROUGH 41)

34

8520142

BRASS BUSHING  (4 REQUIRED)

35

8520141

RUBBER GROMMET (4 REQUIRED)

36

SR-196

BLOWER PAN (BF-10 BF-20)

36

SR-198

BLOWER PAN (BF-30)

37

VF-068

CORD SET ASSEMBLY

38

8720161

BUSHING - HEYCO #SR5KN4

39

R-2395

WIRE ASSEMBLY

40

R-2503

FAN CONTROL

41

R-2396

BLOWER (INCLUDES MOTOR, FAN,
AND FAN HOUSING)

42

11231

FAN CONTROL BRACKET (BF-10)

NOT SHOWN

SR-219

BLOWER HARDWARE PACKAGE

NOT SHOWN

SR-216

HARDWARE PACKAGE

Summary of Contents for BF-10-1













Reviews: