Empire Heating Systems SR-10W-1 Installation Instructions And Owner'S Manual Download Page 1

Page 1

UNVENTED

ROOM HEATER

MODELS

SR-6W-1 SR-10W-1 SR-18W-1 SR-30W-1

SR-30W SHOWN

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death or 

property damage.

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

This appliance may be installed in an aftermarket, 

permanently located, manufactured (mobile) home, 

where not prohibited by local codes.

This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases.

This is an unvented gas-fired heater. It uses air 

(oxygen) from the room in which it is installed. 

Provisions for adequate combustion and ventilation 

air must be provided. Refer to page 6.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water  vapor  is  a  by-product  of  gas  combustion. 

An unvented room heater produces approximately 

one (1) ounce (30ml) of water for every 1,000 BTU’s 

(.3KW’s) of gas input per hour. Refer to page 6.

WARNING

If not installed, operated and maintained 

in  accordance  with  the  manufacturer’s 

instructions, this product could expose you 

to substances in fuel or from fuel combustion 

which can cause death or serious illness.

WARNING

“FIRE, EXPLOSION, AND ASPHYXIATION HAZARD

Improper adjustment, alteration, service, 

maintenance, or installation of this heater or 

its controls can cause death or serious injury.

Read and follow instructions and precautions 

in User’s Information Manual provided with 

this heater.”

INSTALLATION INSTRUCTIONS 

AND OWNER'S MANUAL

Summary of Contents for SR-10W-1

































Reviews: