background image

R-5010

2

The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 (latest edition) and to the National electrical Code, ANSI/NFPA70 (latest edition).
NOTE: Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a qualified service person. More frequent cleaning may be
required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartment,
burners and circulating air passageways of the appliance be kept clean.
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the
appliance. Provide adequate combustion and ventilation air.
The flow of combustion and ventilation air MUST NOT be obstructed.
Provide adequate clearance around air openings into the combustion chamber and adequate accessibility
clearance for servicing and proper operation. NEVER obstruct the front opening of the appliance.

INSTALLATION PRECAUTIONS

This Empire Comfort Systems, Inc. fireplace and its components have been tested and will operate safely when installed in
accordance with this installation manual. Read all instructions before starting installation, then follow these instructions
carefully during installation to maximize fireplace benefit and safety. Report to your dealer any parts damaged in shipment.

The Empire Comfort Systems, Inc. warranty will be voided by, and Empire Comfort Systems, Inc. disclaims any
responsibility for the following actions:

- Installation of any damaged fireplace.
- Modification of the fireplace or any of the components parts thereof.
- Installation other than as instructed by Empire Comfort Systems, Inc.
- Installation and/or use of any component part or accessory not approved by Empire Comfort Systems, Inc. in

combination or assembly with a Empire Comfort Systems, Inc. fireplace, not withstanding any independent
testing laboratory or other third party approval of such component part or accessory.

Any such action may create a possible fire hazard.
Consult your local building codes.

Fireplace Screen.
The fireplace screen must be in place when the fireplace is operating.

TABLE OF CONTENTS

PAGE

A

GENERAL INFORMATION

2

B

OPTIONAL ACCESSORIES

4

C

INSTALLATION OF FIREPLACE

4

D

INSTALLATION OF OPTIONAL ACCESSORIES

7

E

INSTALLATION OF YOUR VENT-FREE GAS LOG HEATER

10

F

MAINTENANCE

10

G

ACCESSORY PARTS

11

H

REPLACEMENT PARTS

12

A

GENERAL INFORMATION

Summary of Contents for VFFB-36D

















Reviews: