background image

38746-0-0118

Page 6

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

The Thermostat Feature may be disabled if desired.

With all three AAA type batteries installed:

1.   Take out one AAA battery.

2.   While re-inserting the AAA battery, Push and hold down the 

thermostat button. This will disable the thermostat feature on 

the transmitter.

Room Thermostat (Transmitter Operation)

The Remote Control can operate as a room thermostat. The 

thermostat can be set to a desired temperature to control the 

comfort level in a room. To activate this function, press the Ther-

mostat Button. 

See Figure 3

. The LCD display on the Transmitter 

will change to show that the room thermostat is “ON” and the 

set temperature is now displayed. 

See Figure 14.

 To adjust the 

set temperature, press the Up or Down Arrow Buttons until the 

desired set temperature is displayed on the LCD screen of the 

Transmitter. 

See Figure 15.

SET TEMPERATURE

ROOM TEMPER ATURE

Figure 14

Figure 15

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the flame height in 

accordance to the difference between the set point temperature 

and the actual room temperatures. As the room temperature gets 

closer to the set point the Smart Function will modulate the flame 

down. To activate this function, press the Thermostat Button until 

the word “SMART” appears to the right of the temperature bulb 

graphic. 

See Figure 16

. To adjust the set temperature, press the 

Up or Down Arrow Buttons until the desired set temperature is 

displayed on the LCD screen of the Transmitter. 

See Figure 17.

NOTE

: When Smart Thermostat is activated, manual flame 

height adjustment is disabled.

Figure 16

Figure 17

Blower Control (Fan)

If the appliance is equipped with a hot air circulating fan, the 

speed of the fan can be controlled by the Proflame system. The 

fan speed can be adjusted through six speeds. To activate this 

function, use the Mode Button 

Figure 3

 to index the fan control 

icon. 

See Figure 18

. Use the Up/Down Arrow Buttons 

Figure 

56

 to turn on off or adjust the fan speed. 

See Figure 19

. A single 

“beep” will confirm reception of the command.

OFF

Figure 18

OFF

Figure 19

Summary of Contents for DVCT36CBP95N-1

















Reviews: