background image

The power cable for the UPA-700 should be unplugged from the outlet during severe electrical storms, or 

when unused for a long period of time.

Only replace the fuse(s) in the UPA-700 with a fuse(s) of proper value and voltage rating. 
The UPA-700 should only be cleaned as directed in the Installation and Operation Manual. Avoid spraying 

liquids directly onto the unit and NEVER spray liquids into the vents. Care should be taken so that small 

objects do not fall into the inside of the unit.
You should seek service for your UPA-700 by qualified service personnel if any of the following occur:
1. The power-supply cord or the plug has been damaged.

 

2. Objects or liquid have fallen or spilled into the vents.

 

3. The unit has been exposed to rain.

 

4. The unit exhibits a marked change in performance.

 

5. The unit has been dropped, or its enclosure or chassis is damaged.

NOTE: TO COMPLETELY DISCONNECT THE UPA-700 FROM THE AC POWER MAINS, DISCONNECT 

THE AC POWER CORD FROM THE AC RECEPTACLE.
NOTE: THE POWER CORD ON THE UPA-700 MUST REMAIN READILY ACCESSIBLE AT ALL TIMES.

!

CAUTION

CAUTION: TO REDUCE THE RISK
OF ELECTRICAL SHOCK, DO
NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

Summary of Contents for UPA-700

























Reviews: