background image

Page 17

Stealth PA-1

Units will be refused by Emotiva for the following:
Product was sent without the WS# 

Product was sent with inadequate packaging. 

Product was damaged in transit. 

Product was shipped collect for shipping charges.

How does state law apply?

  

This warranty gives you specific legal rights, and you may also have other rights which vary from 

state to state.  

What if my product is damaged on the way to you?

Emotiva is not liable for damages that may incur while an item is in transport to us.  Please 

purchase insurance when you ship your item.  If your Product was not adequately packaged, we 

will refuse receipt and the damaged package will be returned to you at your cost.  If you do not 

have the original Emotiva Audio packaging, please check with our sales department to purchase 

replacement-shipping cartons.

How does the Warranty and service apply to international orders? 

The Product Warranty is only valid in the country where the Emotiva product was originally 

shipped via an authorized dealer, distributor, or direct from the Emotiva factory. The Warranty 

is subject to change at any time depending on the laws and regulations within your specific 

country. Please check with your distributor for a complete understanding of the warranty in your 

country. 
If you purchased your Emotiva Product outside of the USA and wish to have it serviced at the 

factory, all freight charges are your responsibility. If you do not have an authorized distributor 

or repair center in your country, your Product must come back to the Emotiva USA factory for 

warranty service. 

Summary of Contents for Stealth PA-1

























Reviews: