EMKO ESM- 20 Series, Manual

Page: 1 / 3

PID TEMPERATURE CONTROL UNITS
ESM-XX20
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operat
� ng Temperature : 0...50°C
Hum � d � ty : 0-90%RH (none condens � ng)
Protect � on Class : IP65 at front, IP20 at rear
We � ght : ESM-4420 : 220 gr. , ESM-4920 : 240 gr.
ESM-7720 : 270 gr. , ESM-9420 : 230 gr.
ESM-9920 : 340 gr.
D � mens � on :
ESM-4420 : (48 x 48mm, Depth: 95mm)
ESM-4920 : (96 x 48mm, Depth: 94.5mm)
ESM-7720 : (72 x 72mm, Depth: 95.5mm)
ESM-9420 : (48 x 96mm, Depth: 94.5mm)
ESM-9920 : (96 x 96mm, Depth: 96mm)
Panel CutOut :
ESM-4420 : (46 x 46mm)
ESM-4920 : (92 x 46mm)
ESM-7720 : (69 x 69mm)
ESM-9420 : (46 x 92mm)
ESM-9920 : (92 x 92mm)
ESM-4920
Temperature Controller ESM - 4920
PS
AS1
AS2 PO
AO1
AO2
ESM-9420
°C
°F
PO
AO1
AO2
PS
AS1
AS2
Temperature
Controller
ESM-9420
Max � mum 15mm / 0.59 � nch
48 mm / 1.89 � nch
10.5 ± 1 mm / 0.41 � nch 84 mm / 3.31 � nch
96
mm
/
3.78
�
nch
ESM-9420
Note-1: If process output � s SSR dr � ver output, pay attent � on to the
1-Before mount � ng the
dev � ce � n your panel,
make sure that the
cutout
� s of the r � ght s � ze.
2-Check
front panel
gasket pos � t � on
3-Insert
the dev � ce
through the cutout. If the
mount
� ng clamps are on
the un � t, put out them
before � nsert � ng the un � t
4-Insert the un � t � n the
panel cut-out from the
front s
� de.
5- Insert the mount
� ng
clamps to the holes that
located top and bottom
s
� des of dev � ce and
screw up the f � x � ng
screws unt � l the un � t
completely � mmob � le
w � th � n the panel.
ESM-9920, ESM-9420, ESM-7720 , ESM-4920, ESM-4420
PID Temperature Control Un
� ts
- 4 d � g � t process (PV) and 4 d � g � t set (SV) d � splay
- Process � nput (TC, RTD)
- Programmable ON/OFF, P, PI, PD and PID control forms
- Adaptat
� on of PID Coeff � c � ents to the system w � th Self-Tune
and AUTO-Tune operat � ons
- Programmable Heat � ng or Cool � ng Funct � ons for Control
Output
- Selectable Alarm Funct
� ons for Alarm Output
ESM ser
� es temperature controllers are des � gned for measur � ng and
controll � ng a process value. They can be used � n many appl � cat � ons
w � th the � r TC and RTD temperature measurement � nput, mult � -
funct � on control outputs, selectable alarm funct � ons.
They are ma � nly used � n glass, plast � c, petro-chem � stry, text � le,
automot � ve and mach � ne product � on � ndustr � es. Accurate and
advanced controll � ng � s performed w � th selectable ON-OFF, P, PI,
PD, PID and Self Tune and Auto Tune PID funct � ons.
SPECIFICATIONS
Process Input :
TC,RTD
Thermocouple (TC): J, K, R, S and T (IEC584.1)(ITS90)
Thermores
� stance (RTD): PT-100 (IEC751)(ITS90)
Measurement Range : Please refer to Table-1 for select � on of � nput
type and scale.
Accuracy : ± 0.25% of scale for thermocouple and thermores � stance
Cold Junct � on Compensat � on : Automat � cally ±0.1°C/1°C
L � ne Compensat � on : Max � mum 10 Ohm
Sensor Break Protect � on : Upscale
Sampl � ng Cycle : 3 samples per second
Input F � lter : 1.0 second
Control Form : ON/OFF, P, PI, PD or PID (Control form can be
programmed by the user)
OUTPUT
Process Output :
Relay (5A@250V at res � st � ve load) or SSR
Dr � ver Output (Max � mum 24mA, Max. 12V )
Alarm Output : Relay(5A@250V at res � st � ve load) or SSR Dr � ver
Output(Alarm Output - 2) (Max � mum 24mA, Max. 12V )
SUPPLY VOLTAGE
24V ( ±15% ) 50/60Hz - 3VA or 24V ( ±%15 ) - 3W
230V ( ±15% ) 50/60 Hz - 3VA
115V ( ±15% ) 50/60 Hz - 3VA
24V ( ±15% ) 50/60 Hz - 3VA
(It must be determ
� ned � n order)
DISPLAY
Process D
� splay :
ESM-4420 : 10.1 mm Red 4 d � g � t LED D � splay
ESM-4920 : 13.2 mm Red 4 d � g � t LED D � splay
ESM-7720 : 13.2 mm Red 4 d � g � t LED D � splay
ESM-9420 : 10.1 mm Red 4 d � g � t LED D � splay
ESM-9920 : 19 mm Red 4 d � g � t LED D � splay
Set Value D � splay :
ESM-4420 : 8 mm Green 4 d � g � ts LED D � splay
ESM-4920 : 8 mm Green 4 d � g � ts LED D � splay
ESM-7720 : 9.1 mm Green 4 d � g � ts LED D � splay
ESM-9420 : 8 mm Green 4 d � g � ts LED D � splay
ESM 9920 : 10.8 mm Green 4 d � g � ts LED D � splay
Leds : PS (Process Set Value), PO (Process Output Status Led) ,
AS1, AS2 (Alarm Set Values), AO1, AO2 (Alarm Output Status
Electr � cal W � r � ngs
Introduct � on Brochure. ENG ESM-XX20 01 V14 10/19