EMG LES CLAYPOOL Installation Information Download Page 4

TIP

RING

SLEEVE

Diagram #8

FROM TONE

OR VOLUME

 LC-PA Page 4

Diagram #10

If the instrument has a Battery Holder:

If your instrument has a 9 or 18 Volt battery holder you can still 

use the EMG Connectors to supply power to the pickups.

Simply cut and strip the wires from the battery clip provided.

Twist the wires together (Red to Red and Black to Black) and 

use the shrink tubing included to cover the connections. 

Soldering the wires is recommended.

9/18 VOLT
 BATTERY
  HOLDER

Cover these connections with the

shrink tubing provided.

BLACK to RING terminal

of the Output Jack

RED to BATTERY OR PICKUP  BUSS

BLACK to RING terminal

of the Output Jack

RED TO BATTERY BUSS (+18Volts)

Diagram #11

BATTERY

NEG (-)

RED to BATTERY BUSS

Soldering to the 152B Panel Jack:

If your instrument has a long panel jack like the one below

you will have to solder the output cable as shown. 

   Ground (Black) to the sleeve

   Signal (White) to the Tip 

   Battery Negative (Black) to the Ring

     

-  9V  +

-  9V  +

-  9V  +

T

R

S

RED

BLACK

Diagram #7

Two Pickups

Two Volume

One Tone

Toggle Style Switch

  

 

Diagram #9

Installation with Mounting Standoffs:

The included mounting standoffs may assist in the pickup 

installation process for certain instruments. The standoffs 

slip onto the long adjustment screws prior to mounting 

the pickups. This prevents the screws from being driven 

too deeply into the instrument. The standoffs are 

not

intended for use with the short adjustment screws. 

+18 Volt Wiring Option:

If you want to operate your instrument at +18 Volts for more 

headroom then use 2 batteries wired as below. 

Also, if you are using any type of EQ in your instrument 

(EMG-BT, BQ) or anything that boosts the pickup signal then

+18 Volts is recommended.

Solder the Black and Red

wires together and cover

the connection with shrink

tubing, or other insulation.

VOLUME

B122rH

VOLUME

B122rH

TONE

B124rH

NECK PICKUP

BRIDGE PICKUP

BATTERY

NEG (-)

RED

RED

RED

GROUND

BRIDGE P/U

NECK P/U

OUTPUT

-  9V  +

NK VOLUME

BR VOLUME

T

R

S

MASTER

  TONE

OUTPUT CABLE

LONG ADJUSTMENT SCREW

MOUNTING STANDOFF

Summary of Contents for LES CLAYPOOL

Page 1: ...200 1 200 30 48 30 48 875 875 22 22 22 22 750 750 19 19 NOTE EMG Metal Works Pickups may be direct mounted NOTE EMG Metal Works Pickups may be direct mounted with either short or long adjustment screws depending with either short or long adjustment screws depending on what works best for your instrument on what works best for your instrument See Diagram 9 on page 4 for instructions on using the Se...

Page 2: ...own Plug a connector cable from the volume control to the tone control Plug the output cable onto the tone control as shown 4 Connect the wires of the output cable to the output jack by pushing the connectors on as shown WHITE wire to the TIP T contact BLACK wire to the SLEEVE S contact BLACK battery negative wire to the RING R contact 5 Using the battery buss insert the RED wire of the pickup and...

Page 3: ...type output jack your instrument has 1 Determine which type output jack your instrument has A Stereo 12B type is Included but if you have a long panel jack A Stereo 12B type is Included but if you have a long panel jack a SwitchCraft 152B Long Panel Jack will be required a SwitchCraft 152B Long Panel Jack will be required 2 Remove the strings remove any existing pickups and controls 2 Remove the s...

Page 4: ...o the Tip Battery Negative Black to the Ring 9V 9V 9V T R S RED BLACK Diagram 7 Two Pickups Two Volume One Tone Toggle Style Switch Diagram 9 Installation with Mounting Standoffs The included mounting standoffs may assist in the pickup installation process for certain instruments The standoffs slip onto the long adjustment screws prior to mounting the pickups This prevents the screws from being dr...

Reviews: