Emerson USB Fieldbus Interface User Manual Download Page 10

Page: 10 / 59

Software installation and device setup

Topics covered in this chapter:

•

System requirements

•

Install the Fieldbus Interface Configuration utility

•

Install the Communication DTM software

•

Install the Emerson DTM Library

•

Setup and connection

•

Connect to a live fieldbus segment

Perform software installation and device setup in the following order:
1.

Install the Fieldbus Interface Configuration utility.

This allows you to configure the USB Fieldbus Interface and connected
fieldbus devices.

Install the Communication DTM software.

This enables DTM support for connected fieldbus devices.

Install the Emerson DTM Library.

This allows you to use DTMs associated with Emerson devices through an
FDT Frame Application.

Note

Device DTMs are usually acquired from device suppliers. Contact your device supplier if you

have a non-Emerson device and install the appropriate third-party DTM library.

Set up and configure connected fieldbus devices.

3.1

System requirements

Supported operating systems

Windows 8.0 and 8.1
Windows 7 (32- or 64-bit)
Windows XP Home or Professional (32-bit) SP3

Hard disk space

At least 500MB

Hardware

USB 1.1 or USB 2.0 port

User's Manual

May 2014

Summary of Contents for USB Fieldbus Interface




























































Search results

Summary of Contents for USB Fieldbus Interface

Reviews:

Related manuals for USB Fieldbus Interface

Brands by name

Popular brands

Emerson USB Fieldbus Interface, User Manual

Search results

Summary of Contents for USB Fieldbus Interface

Reviews:

Related manuals for USB Fieldbus Interface

Brands by name

Popular brands