Emerson SM-EtherCAT User Manual Download | Manualshive

Page: 18 / 70

background image

18

SM-EtherCAT User Guide

www.controltechniques.com

Issue Number: 2

5.3

Saving parameters to the drive

On the Unidrive

SP, Affinity, Digitax ST and Commander SK

to avoid loss of the

configured settings when the drive is powered down it is necessary to write 1000 to
Pr

MM.00

followed by pressing the reset button to perform a drive save. On Mentor MP

Pr

MM.00

needs to be set to a value of ‘SAVE’ followed by pressing the reset button.

To store drive parameters:

•

Set Pr

MM.00

to 1000 (Mentor MP Pr

MM.00

=SAVE).

•

Press the red RESET button.

The drive will store all parameters (except Menu 20) but the operation of the SM-
EtherCAT will not be affected. Changes made to the SM-EtherCAT configuration
parameters will not take effect until the SM-EtherCAT is reset.

5.4

Re-initialising the SM-EtherCAT

Changes to the SM-EtherCAT configuration in menu 15, 16 or 17 parameters (menu 15
and 16 on Affinity, menu 15 on Commander SK) will not take effect until the SM-
EtherCAT has been re-initialised.

To re-initialise SM-EtherCAT:

1. Set Pr

MM.32

to ON.

2. When the sequence has been completed, Pr

MM.32

will be reset to OFF.

3. The SM-EtherCAT will re-initialise using the updated configuration.

5.5

Re-initialise all Solutions Modules

To re-initialise all Solutions Modules fitted on a Unidrive SP, Affinity or Digitax ST:

1. Set Pr

MM.00

to 1070.

2. Press the red RESET button on the drive.

Unidrive-SP, Mentor MP, Affinity and Digitax ST: Menu 20 applications parameters may
be saved if an Application Module is fitted, menu 20 is stored in the Application
Module’s memory. See the relevant Application Module documentation for more
information. If the drive is running on backup supply only, Pr

MM.00

must be set to 1001

to perform a save.

This saves only drive and module parameters and not SM-EtherCAT related objects.

NOTE

NOTE

Table 5.4 SM-EtherCAT re-initialise

SM-EtherCAT re-initialise

Pr

MM.32

Default

0 (OFF)

Range

0 (OFF) to 1 (ON)

Access

RW

The above sequence does NOT store the SM-EtherCAT configuration parameters in the
drive or the SM-EtherCAT’s internal FLASH memory. This parameter will change back to
off immediately and as such the change may not be visible on the display.

NOTE

This sequence does NOT store the SM-EtherCAT configuration parameters in the drive
or the SM-EtherCAT FLASH memory.

On Commander SK drives,

Pr 00.00

is not available.

NOTE

NOTE

«
...
16
17
18
19
20
...
»

Summary of Contents for SM-EtherCAT







































































Reviews:

No comments

Related manuals for SM-EtherCAT

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

SANbox 5000 Series

Brand: Qlogic Pages: 8

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 1

Cleveland Controls RSS-498-013

Brand: UNICONTROL Electronic Pages: 2

Brand: AVE Pages: 2

Brand: Gefen Pages: 31

Brand: ORiNG Pages: 2

TIMEGUARD WF10COM

Brand: Theben Pages: 35

Brand: Ableconn Pages: 16

Brand: Conceptronic Pages: 7

Brand: Accton Technology Pages: 7

Brand: Jerguson Pages: 4

Brand: Cabletron Systems Pages: 54

Brand: TESmart Pages: 4

Brand: Zhuoyi Pages: 2

Brand: Extron electronics Pages: 1

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands