Emerson Rosemount Oxymitter DR Reference Manual Download Page 87

Page: 87 / 98

Upgrade Rosemount

™

Oxymitter DR

to full Oxymitter

Figure B-1: Component Replacement

A. Screws

B. Rosemount OXT adapter board

C. Screws

D. Electronic assembly

Procedure

1. Remove power from the Rosemount Oxymitter DR.
2. Remove the left and right covers from the Rosemount Oxymitter termination

housing.

3. Remove and discard screws and Rosemount OXT adapter board (A and B,

Figure

B-1

) located at the right side of the termination housing.

4. Place the new Rosemount Oxymitter electronic assembly (D) near the right side of

the termination housing.

5. Plug the white connector with the two black wires into the white socket on the

bottom power supply card.

6. Insert the electronics assembly into the termination housing. Ensure the black four-

wire connector remains outside the housing and in the slot provided in the top card
of the electronics assembly.
The electronics assembly should seat on the bulkhead pins easily. Do not force the
assembly into place.

Reference Manual

Upgrade Rosemount

™

Oxymitter DR to full Oxymitter

00809-0100-4880

October 2019

Rosemount Oxymitter DR

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands