Emerson Rosemount Oxymitter DR Reference Manual Download Page 61

Page: 61 / 98

Figure 4-4: Ceramic Diffuser Element Replacement

A. Threaded probe flange

B. M5-0.8 x 5 mm locking set screw (use 2.5 mm hex key)

C. Spanner wrench

D. Ceramic diffusion element

E. M5-1 x 6 mm setscrew (use 3 mm hex key)
F. Vee deflector

G. Cement fillet
H. Cement port

I. Flame arrestor hub

4. If equipped with the optional ceramic diffusion assembly, remove and discard the

setscrews and remove the vee deflector (

Figure 4-4

). Use spanner wrenches from

the probe disassembly kit (

Table 4

) to turn the hub free from the retainer. Inspect

the diffusion element. If damaged, replace the element.

5. Loosen the four socket head cap screws from the cell and flange assembly.
6. Remove the assembly and the corrugated cell.

Reference Manual

Maintenance and service

00809-0100-4880

October 2019

Rosemount Oxymitter DR

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands