Emerson Rosemount Oxymitter DR Reference Manual Download Page 58 | Manualshive

Page: 58 / 98

background image

Figure 4-2: Heater Strut Assembly

A. V-deflector

B. Ceramic support rod

C. Wire loop

D. Ceramic diffuser assembly

E. Cell flange
F. Heater

8. When replacing the strut, orient the probe so that the small calibration gas tuble

lays at the 6 o'clock position of the probe tube. Align the slot on the heater plate
with the calibration gas line in the probe tube. Slide the strut into the probe tube.
The strut turns to align the hole on the back plate of the strut with the calibration
gas line. When the hole and the calibration gas line are aligned correctly, the strugt
will slide in the rest of the way.

9. As the strut installation nears completion, install the guide rod into the calibration

gas tube to assist in guiding the calibration gas tube through the hole in the end of
the strut.

10. Push down the back plate of the strut to make sure you have spring tension and

then tighten the three screws on the back plate.

11. Replace the CAL and REF gas silicone tubes.
12. Install the termination housing per

Replace terminal block

.

13. Follow the instructions in

to install the probe in the stack or duct.

Maintenance and service

Reference Manual

October 2019

00809-0100-4880

58

Emerson.com/Rosemount

«
...
56
57
58
59
60
...
»

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Related manuals for Rosemount Oxymitter DR

Brand: Olympus Pages: 4

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 84

Brand: Aqualytic Pages: 130

Brand: Scaletron Pages: 63

Brand: MULTISPAN Pages: 4

FrameSaver SLV Series

Brand: Paradyne Pages: 39

Brand: Opus Technologies Pages: 24

Brand: Konica Minolta Pages: 92

Brand: Keithley Pages: 338

Brand: Liquid Controls Pages: 16

Brand: Heyuan Intelligence Pages: 14

Brand: Jaquet Pages: 16

Brand: OHAUS Pages: 28

Brand: Velp Scientifica Pages: 32

Brand: IFM Pages: 45

Brand: GARO Pages: 15

Brand: Mountz Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands