Emerson Rosemount CT5100 Reference Manual Download Page 155 | Manualshive

Page: 155 / 179

background image

15. Secure the gas temperature sensor wiring harness with cable ties and cable clips in

the locations that were noted down in

.

16. Fit the top cover and restart the analyzer.

12.20

Replacing the pressure sensor

Figure 12-17: Replacing the Pressure Sensor

A. Bulkhead adaptor

B. Dowty washer

C. Pressure sensor

D. Pressure sensor electrical connector

Procedure

1. Shut down the analyzer.

Shutdown procedure

.

2. Remove the analyzer top cover.

Removing the top cover

.

3. Disconnect the pressure sensor electrical connector (D).
4. While holding the bulkhead adaptor (A) steady unscrew the pressure sensor (C).
5. Discard the unserviceable pressure sensor.
6. Inspect the new pressure sensor for damage.
7. Install the replacement pressure sensor (C) and dowty washer (B) onto the bulkhead

adaptor (A). Hold the bulkhead adaptor steady while tightening the pressure
sensor.

8. Reconnect the pressure sensor electrical connector (D) to the pressure sensor.

Reference Manual

Repair and replacement

00809-0100-4512

October 2019

Reference Manual

155

«
...
153
154
155
156
157
...
»

Summary of Contents for Rosemount CT5100




















































































































































































Reviews:

No comments

Related manuals for Rosemount CT5100

Brand: Keithley Pages: 49

Brand: Aaronia Pages: 47

Brand: Eagle Eye Pages: 3

Brand: VALTRONICS Pages: 13

Brand: JIANGSU Pages: 8

Brand: LaserLine Pages: 24

TEC SourceMeter 2510

Brand: Keithley Pages: 244

Brand: Kawai Pages: 112

Brand: Yamaha Pages: 6

Brand: Hanna Instruments Pages: 9

Brand: Vigor Equipment Pages: 12

Dakota Ultrasonics ZX-2

Brand: ABQ Industrial Pages: 27

Brand: KALATEL Pages: 38

Brand: LaserLine Pages: 11

Brand: E+E Elektronik Pages: 20

Brand: Brooks Pages: 64

Brand: brena Pages: 26

Brand: Gait up Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands