Emerson Rosemount Apex Reference Manual Download Page 51 | Manualshive

Page: 51 / 124

background image

Reference Manual

00809-0100-4731, Rev FA
April 2003

APEX

™

and APEX Sentry

™

Radar Gauge

www.rosemount.com

Section 3

Configuration

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
Basic Configuration Parameters  . . . . . . . . . . . . . . . . . . . . page 3-2
Field Configuration Using the Integral  Display Option   . page 3-6
Model 275 HART Communication Option . . . . . . . . . . . . . page 3-15
AMS Configuration Tool Option   . . . . . . . . . . . . . . . . . . . . page 3-21
Radar Configuration Tool (RCT) Option  . . . . . . . . . . . . . . page 3-25

NOTE

All information included refers to both the APEX Radar Gauge
and the APEX Sentry Radar Gauge unless otherwise stated.

The HART Communicator manual provides detailed instructions on the use
and features of the HART Communicator. For information on all the
capabilities of the HART Communicator, refer to the HART Communicator
Product Manual (document 00809-0100-4275).

SAFETY MESSAGES

Procedures and instructions in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
potentially raises safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.

Explosions could result in death or serious injury:

•

Verify that the operating environment is consistent with the appropriate
hazardous locations certifications.

•

Before connecting a HART-based communicator in an explosive atmosphere,
make sure the instruments in the loop are installed in accordance with
intrinsically safe or non-incendive field wiring practices.

•

Do not make connections to the serial port or NiCad recharger jack in an
explosive atmosphere.

Failure to follow safe installation and servicing guidelines could result in death or
serious injury:

•

Make sure only qualified personnel perform these procedures.

•

Use the equipment only as specified in this manual. Failure to do so may
impair the protection provided by the equipment.

•

Do not perform any service other than those contained in this manual unless
you are qualified.

As a matter of routine, the APEX Radar Gauge and all other equipment in your
tank should be shut off prior to entering the tank.

«
...
49
50
51
52
53
...
»

Summary of Contents for Rosemount Apex





























































































































Reviews:

No comments

Related manuals for Rosemount Apex

Brand: X-Rite Pages: 80

Brand: Xsens Pages: 4

Brand: Eastron Pages: 2

Brand: EASTERN INSTRUMENTS Pages: 3

PowerCross-Laser 8 S

Brand: LaserLiner Pages: 64

ClimaHome-Check Plus

Brand: LaserLiner Pages: 10

MeterMaster Plus

Brand: LaserLiner Pages: 104

Brand: LaserLiner Pages: 52

LaserRange-Master T2

Brand: LaserLiner Pages: 52

Brand: LaserLiner Pages: 5

CombiRangeXtender 40

Brand: LaserLiner Pages: 84

SuperCross-Laser 2P

Brand: LaserLine Pages: 92

MoistureFinder Compact

Brand: LaserLine Pages: 56

LaserRange-Master Gi7 Pro

Brand: LaserLiner Pages: 56

Brand: Laser Tools Pages: 4

SmartVision-Laser

Brand: LaserLiner Pages: 56

Brand: Keithley Pages: 18

Brand: Chroma Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands