Emerson Rosemount 8800D Series Reference Manual Download Page 159

Page: 159 / 192

Reference Manual

00809-0100-4772, Rev FA

Electronics Verification

March 2016

Electronics Verification

149

Appendix C

Electronics Verification

Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 149
Electronics verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 150

C.1

Safety messages

Instructions and procedures in this section may require special precautions to ensure the
safety of the personnel performing the operations. Refer to the following safety messages
before performing any operation in this section.

Explosions could result in death or serious injury.



Do not remove the transmitter cover in explosive atmospheres when the circuit is
alive.



Before connecting a F

OUNDATION

™

Fieldbus-based communicator in an explosive

atmosphere, make sure the instruments in the loop are installed in accordance
with intrinsically safe or non-incendive field wiring practices.



Verify the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.



Both transmitter covers must be fully engaged to meet explosion-proof
requirements.

Failure to follow these installation guidelines could result in death or serious
injury.



Make sure only qualified personnel perform the installation.

Remove power before removing the electronics housing.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Emerson Rosemount 8800D Series, Reference Manual, Page: 159 / 192

Search results

Summary of Contents for Rosemount 8800D Series

Reviews: