manualshive.com logo in svg

Emerson Rosemount 3152, Reference Manual

Share
Download
Emerson Rosemount 3152 Reference Manual Download Page 75

Reference Manual 

00809-0100-4835 Rev BE 
February 2018

Rosemount 3150 Series 

Maintenance & Troubleshooting

 

66 

Table 5-3 – Troubleshooting 

SYMPTOM 

POTENTIAL 

SOURCE 

CORRECTIVE ACTION 

High Output 

Primary Element 

Check for restrictions at primary element, improper installation or 
poor condition.  Note any changes in process fluid properties that 
may affect output. 

Impulse Piping 

•

Check for leaks or blockage.

•

Ensure blocking valves are fully open.

•

Check for entrapped gas in liquid lines, or liquid in dry lines.

•

Ensure that density of fluid in impulse line is unchanged.

•

Check for sediment in transmitter process flanges.

Transmitter 

Electronics 

Make sure that filter pins and the sensor module connections are 
clean.  If the electronics are still suspect, substitute new 
electronics. 

Transmitter 

Electronics Failure 

Determine faulty circuit board by trying spare electronics 
assembly or terminal block assembly.  Replace faulty assembly. 

Sensor Module 

NOTE: S

ee

 Sensor Module Checkout 

section.  The sensing 

element is not field repairable and must be replaced if found to be 
defective.  See 

Disassembly Procedure

 for instructions on 

disassembly.  Check for obvious defects (i.e. punctured isolating 
diaphragm, etc.) and contact Rosemount Nuclear. 

Power Supply 

Check the power supply output voltage at the transmitter. 

Low Output 

or No Output 

Primary Element 

Check the installation and condition of primary element. 
Note any changes in process fluid properties that may affect 
output. 

Loop Wiring 

 

CAUTION 

Do not use more than 55 volts to check the loop, or 
damage to the transmitter electronics may result. 

•

Check for inadequate voltage to the transmitter.

•

Check the milliamp rating of the power supply against the total
current being drawn for all transmitters being powered.

•

Check for intermittent shorts, open circuits, or multiple grounds.

•

Check for proper polarity at the signal terminal.

•

Check loop impedance.

•

Check wire insulation to detect possible shorts to ground.

Impulse Piping 

•

Ensure that the pressure connection is correct.

•

Check for leaks or blockage.

•

Check for entrapped gas in liquid lines, or liquid in dry lines.

•

Check for sediment in transmitter process flanges.

•

Ensure that blocking valves are fully open and that bypass
valves are tightly closed.

•

Ensure that density of fluid in the impulse line is unchanged.

Transmitter 

Electronics 

Connections 

•

Ensure that calibration adjustments are in allowable range.

•

Check for short in sensor leads.

•

Make sure filter pins are clean, and check the sensor module
connections.

•

If the electronics are still suspect, substitute new electronics.

Continued on Next Page 

Summary of Contents for Rosemount 3152





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands