manualshive.com logo in svg

Emerson Rosemount 285, Quick Installation Manual, Page: 6 / 12

Share
Download
Emerson Rosemount 285 Quick Installation Manual Download Page 6

Quick Installation Guide

00825-0100-4031, Rev AA

April 2005

Duct Mount 285 Annubar

6

3. Push the flange and gasket flush against the duct wall; align the flow arrow in the 

direction of flow and fasten the flange to the duct using the #12 sheet metal screws 
provided.

Figure 5.  

4. On the opposite side of the duct, place the 

5

/

16

-in. lock washer over the stud, screw on 

the 

5

/

16

 nut, and tighten. Depending on the pressure in the duct, it may be necessary to 

add some high temperature gasket sealant where the stud protrudes through the duct 
wall.

Duct Mount With Compression Fitting (Annubar type D2)

1. Place gasket against the mounting flange. Alternatively, a high-temperature gasket 

sealant may be used.

2. Push the flange and gasket flush against the duct wall, and fasten the flange to the duct 

using the #12 sheet metal screws provided.

STUD

1/4" SHEET METAL SCREWS

2

85

/15

-4

90

01

6-

90

1,

15

-4

90

01

7-

90

1

STUD

1/4" SHEET

METAL SCREWS

28

5/

15-

4900

37

-9

01

,

15

-4

90

03

8-

90

1

STUD

LOCK WASHER

NUT

ANNUBAR

DUCT

DUCT

LOCK WASHER

NUT

STUD

ANNUBAR

285

/15

-490

01

8-

90

1, 

/15

-4

9

0039

-901

00825-0100-4031_Rev AA.fm  Page 6  Monday, March 28, 2005  11:10 AM

Summary of Contents for Rosemount 285













Reviews:

No comments