Emerson Rosemount 2051 Reference Manual Download Page 98 | Manualshive

Page: 98 / 228

background image

88

Reference Manual

00809-0100-4107, Rev BA

Section 6: Troubleshooting

April 2013

Troubleshooting

6.4.2

Removing terminal block

Electrical connections are located on the terminal block in the compartment labeled “FIELD
TERMINALS.”

1.

Remove the housing cover from the field terminal side.

2.

Loosen the two small screws located on the assembly in the 9 o’clock and 5 o’clock
positions relative to the top of the transmitter.

3.

Pull the entire terminal block out to remove it.

6.4.3

Removing the electronics board

The transmitter electronics board is located in the compartment opposite the terminal side. To
remove the electronics board see

Figure 4-1 on page 58

and perform following procedure:

1.

Remove the housing cover opposite the field terminal side.

2.

If you are disassembling a transmitter with a LCD/LOI Display, loosen the two captive
screws that are visible (See

for screw locations). The two screws

anchor the LCD/LOI Display to the electronics board and the electronics board to the
housing.

Note:

The electronics board is electrostatically sensitive; observe handling precautions for
static-sensitive components

3.

Using the two captive screws, slowly pull the electronics board out of the housing. The
sensor module ribbon cable holds the electronics board to the housing. Disengage the
ribbon cable by pushing the connector release.

Note:

If an LCD/LOI is installed, use caution as there is an electronic pin connector that interfaces
between the LCD/LOI and electronics board.

6.4.4

Removing sensor module from the electronics housing

1.

Remove the electronics board. Refer to

“Removing the electronics board” on page 88

Important

To prevent damage to the sensor module ribbon cable, disconnect it from the electronics board
before you remove the sensor module from the electrical housing.

2.

Carefully tuck the cable connector completely inside of the internal black cap.

See

“Safety messages” on page 81

for complete warning

«
...
96
97
98
99
100
...
»

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 110

Portatone PSR-5700

Brand: Yamaha Pages: 79

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 108

Brand: Bamo Pages: 17

Brand: Lutron Electronics Pages: 13

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

Brand: Tektronix Pages: 20

FlowStar2 LB 514

Brand: BERTHOLD TECHNOLOGIES Pages: 130

Brand: Megger Pages: 8

Brand: Alpes Lasers Pages: 41

Brand: Thermo Scientific Pages: 56

Brand: Velleman Pages: 15

PHYSICS line C.A 832

Brand: Chauvin Arnoux Pages: 43

Brand: Agilent Technologies Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands