Emerson Rosemount 2051 Reference Manual Download Page 65

Page: 65 / 228

Reference Manual

00809-0100-4107, Rev BA

Section 4: Electrical Installation

April 2013

Electrical Installation

4.4

Configuring transmitter security

There are four security methods with the Rosemount 2051 transmitter.



Security switch



HART Lock



Configuration Buttons lock



LOI password

Figure 4-2. 4-20 mA electronics board

A. Alarm
B. Security

Note

1-5 Vdc Alarm and Security switches are located in the same location as 4-20 mA output boards.

4.4.1

Setting security switch

The security switch is used to prevent changes to the transmitter configuration data. If the
security switch is set to the locked location (

), any transmitter configuration requests sent via

HART, LOI, or local configuration buttons will be rejected by the transmitter and the transmitter
configuration data will not be modified. Reference

Figure 4-2

for the location of the security

switch. Follow the steps below to enable the security switch.

Set loop to manual and remove power.

Remove transmitter housing cover.

Use a small screwdriver to slide the switch to the lock (

) position.

Replace transmitter housing cover; cover must be fully engaged to comply with
explosion proof requirements.

Without LCD Meter

With LCD/LOI Display

Summary of Contents for Rosemount 2051





































































































































































































































Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands

Emerson Rosemount 2051, Reference Manual

Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands