Emerson Rosemount 2051 Reference Manual Download Page 20

Page: 20 / 228

Reference Manual

00809-0100-4107, Rev BA

Section 2: Configure

April 2013

Configuration

Figure 2-1. Wiring the Transmitter (4-20 mA HART)

A. Vdc supply

B. R



250 (necessary for HART communication only)

2.4.2

Configuration tools

Figure 2-2. Wiring the Transmitter (1-5 Vdc Low Power)

A. DC power supply
B. Voltmeter

Configuring with a Field Communicator

There are two interfaces available with the Field Communicator: Traditional and Dashboard
interfaces. All steps using a Field Communicator will be described using Dashboard interfaces.

Figure 2-3 on page 11

shows the Device Dashboard interface. As stated in

Section 2.3-System

readiness

, it is critical that the latest DD’s are loaded into the Field Communicator. Visit

www.emersonprocess.com or www .hartcomm.org to download latest DD library.

Field Communicator menu trees and fast keys are available in

Appendix C: Field Communicator

Menu Trees and Fast Keys

Summary of Contents for Rosemount 2051





































































































































































































































Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands

Emerson Rosemount 2051, Reference Manual

Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands