Emerson Rosemount 2051 Reference Manual Download Page 11

Page: 11 / 228

Reference Manual

00809-0100-4107, Rev BA

Section 1: Introduction

April 2013

Introduction

Section 1

Introduction

1.1

Using this manual

The sections in this manual provide information on installing, operating, and maintaining the
Rosemount 2051. The sections are organized as follows:

Section 2: Configuration

provides instruction on commissioning and operating Rosemount

2051 Transmitters. Information on software functions, configuration parameters, and online
variables is also included.

Section 3: Hardware Installation

contains mechanical installation instructions, and field

upgrade options.

Section 4: Electrical Installation

contains electrical installation instructions, and field upgrade

options.

Section 5: Operation and Maintenance

provides detailed information on calibrating and

changing HART Revisions.

Section 6: Troubleshooting

provides troubleshooting techniques for the most common

operating problems.

Section 7: Safety Instrumented Systems Requirements

provides identification, installation,

configuration, operation and maintenance, and inspection information for Safety Intrumented
Systems.

Appendix A: Specifications and Reference Data

supplies reference and specification data, as well

as ordering information.

Appendix B: Product Certifications

contains intrinsic safety approval information, European

ATEX directive information, and approval drawings.

Appendix C: Field Communicator Menu Trees and Fast Keys

provides full menu trees and

abbreviated fast key sequences for commissioning tasks.

Appendix D: Local Operator Interface

provides detailed LOI menu trees.

Summary of Contents for Rosemount 2051





































































































































































































































Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands

Emerson Rosemount 2051, Reference Manual

Search results

Summary of Contents for Rosemount 2051

Reviews:

Related manuals for Rosemount 2051

Brands by name

Popular brands