background image

OUTLET BOX

BLACK SUPPLY WIRE

BLACK/WHITE RECEIVER WIRE

BLACK FAN WIRE

BLUE FAN WIRE

BLUE RECEIVER 
WIRE

YELLOW FAN WIRE

YELLOW RECEIVER WIRE

CEILING COVER

WHITE RECEIVER WIRE

WHITE FAN WIRE

WIRE CONNECTOR

RECEIVER

WHITE SUPPLY
WIRE

SUPPLY GROUND
WIRE (GREEN OR 
BARE)

HANGER BALL
GROUND WIRE
(GREEN)

HANGER BRACKET
GROUND WIRE
(GREEN)

HANGER BRACKET

BLACK RECEIVER WIRE

OPEN 

PORTION OF 

RECEIVER 

HERE

7

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.

WARNING

!

Figure 9

How to Wire Your Ceiling Fan

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician. 

CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.

1. Pull the wire leads, coming from the end of the

downrod, and the supply wires through the open
side of the hanger bracket. (Figure 9).

2. Position the SW105 Receiver (supplied) in the

ceiling cover so that the flat side of the receiver
faces up and the open portion of the receiver is to
the right, as shown in Figure 9.

3. Using wire connectors (supplied), make wiring

connections as follows (Figure 9 and 10):

a. Connect the white fan wire and the white supply

wire to the white receiver wire (AC IN N/
MOTOR N).

b. Connect the black fan wire to the black receiver

wire (TO MOTOR L).

c. Connect the black supply wire to the black/white

receiver wire (AC IN L).

d. Cut off the ends of the blue and yellow receiver

wires and strip back insulation 1/2-inch from the
ends of the wires.

e. Connect the blue fan wire to the blue receiver

wire (BOTTOM LIGHT).

f. Connect the yellow fan wire to the yellow

receiver wire (UPPER LIGHT).

g. Connect the green ground wires from the

hanger bracket and the hanger ball to the supply
ground wire (bare or green).

Summary of Contents for RAPHAEL CF2605PW00

















Reviews: