Emerson Liebert PEX Series, User Manual

Page: 68 / 109

Chapter 5 iCOM Controller 63
Liebert.PEX2 Series Air Conditioner User Manual
Parameters Default Description
S609 CAL DS2 29°C
Sum of the calibrated value and return air humidity measured by digital scroll 2NTC
sensor. This value is engaged in the calculation
S610 OUT SNS °C Outdoor Sensor
S611 CAL OUT +0.0K Calibrated Outdoor Sensor
S613 TEMP A +0.0K Calibrated value of temperature sensor A
S614 CAL A °C Calculated value corresponding to temperature sensor A
S615 HUM A +0.0% Calibrated value of humidity sensor A
S616 CAL A 44.0% Calculated value corresponding to humidity sensor A
S617 TEMP B TH Calibrated value of temperature sensor B
S618 TYPE B +0.0K Type of temperature sensor B
S619 CAL B °C Calculated value corresponding to temperature sensor B
S620 HUM B +0.0% Calibrated value of humidity sensor B
S621 CAL B 44.0% Calculated value corresponding to humidity sensor B
S622 TYPE C TH Type of temperature sensor C
S624 FC SNSR -
Free cooling temperature sensor. PTC or NTC sensor can be configured according to the
actual configuration
S625 FC SNSR +0°C Calibrated value of free cooling temperature sensor
S626 CAL FC °C Calculated value of free cooling temperature sensor
S627 SUP SNSR NTC Air supply temperature sensor. PTC or NTC sensor can be configured
S628 SUP TEMP +0.0K Calibrated value of air supply temperature sensor
S629 CAL SUP °C Calculated value of air supply temperature sensor
S630 TEMP C +0.0K Calibrated value of temperature sensor C
S631 CAL C °C Calculated value of temperature sensor C
S632 HUM C +0.0% Calibrated value of humidity sensor C
S633 CAL C % Calculated value of humidity sensor C
5.7.8 NETWORK SETUP
The NETWORK SETUP menu is used to set the parameters when the system is in a network subject to the monitoring
of a host. See Table 5-27 for parameter descriptions.
Table 5-27 Descriptions of NETWORK SETUP parameters
Parameters Default Setting range Description
S802 #UNITS 1 1 ~ 32 Range: 1 ~ 32
S803 TEAMWORK No No, 1, 2 Range: No, 1, 2
S824 MON ADD 3 1 ~ 99 Monitoring address No. of the unit
S825 MON T.O. No No, 1, 2 Monitoring Timeout
S825 MON H.S. 3 1 ~ 99 Monitoring Handshake
S831 CS CTRL No
Save, Load,
No Save the parameter set through MON ADD to the iCOM controller.
‘No’ means not saved
S831 CS STAT Change Change, Valid
Indication of the saving state of the parameter set through MON
ADD. ‘Change’ means that the parameter is changed but not saved.
‘Valid’ means that the setting is valid and saved
S832 NW CTRL No
Save, Load,
No Save the parameter set through U2U GRP to the iCOM controller.
‘No’ means not saved
S832 NW STAT Valid Change, Valid
Indication of the saving state of the parameter set through U2U
GRP. ‘Change’ means that the parameter is changed but not saved.
‘Valid’ means that the setting is valid and saved
S835 MON PROT Vlcty
Vlcty, HN,
IGM, No Host monitoring protocol setting. Range: Vlcty (Velocity uses
intelligent card), HN (Hironet), IGM (ECA2), No
S836 IP #1 192
S836 IP #2 168
S836 IP #3 254
S836 IP #4 1
- Set IP address
S837 NM #1 255
S837 NM #2 255
S837 NM #3 255
S837 NM #4 0
- Set subnet mask