Emerson Liebert NXL Operation And Maintenance Manual Download | Manualshive

Page: 2 / 72

background image

B

ATTERY

C

ABINET

P

RECAUTIONS

The following warning applies to all battery cabinets supplied with UPS systems. Additional warn-

ings and cautions applicable to battery cabinets may be found in Important Safety Instructions and

3.4 - Battery Maintenance

.

Contacting Liebert for Support

Contact Emerson Network Power Liebert Services for information or repair service in the United

States at 1-800-LIEBERT (1-800-543-2378).
For repair or maintenance service outside the 48 contiguous United States, contact Liebert Services,

if available in your area. For areas not covered by Liebert Services, the authorized distributor is

responsible for providing qualified, factory-authorized service.
Have the following information available before calling Liebert Services:
Part Numbers:  ________________________________________________________________
Serial Numbers:  _______________________________________________________________
kVA Rating:  __________________________________________________________________
Date Purchased: _______________________________________________________________
Date Installed:  ________________________________________________________________
Location: _____________________________________________________________________
Input Voltage/Frequency:  ______________________________________________________
Output Voltage/Frequency:  _____________________________________________________
Battery Reserve Time:  _________________________________________________________

!

WARNING

Internal battery strapping must be verified by manufacturer prior to moving a battery cabinet

(after initial installation).
• Battery cabinets contain non-spillable batteries.
• Keep units upright.
• Do not stack.
• Do not tilt.
Failure to heed this warning could result in smoke, fire or electric hazard.
Call 1-800-LIEBERT before moving battery cabinets (after initial installation).

«
1
2
3
4
...
»

Summary of Contents for Liebert NXL









































































Reviews:

No comments

Related manuals for Liebert NXL

DryStar 2000 CAN

Brand: HEIDELBERG Pages: 40

Brand: Kärcher Pages: 188

Custom power box

Brand: Barco Pages: 19

Brand: RATHI Pages: 19

Brand: Facom Pages: 44

NEX Formulation Tank

Brand: GC Water Pages: 17

Brand: CAB Pages: 42

Brand: WDT Pages: 44

Brand: handtmann Pages: 4

Brand: Wood-mizer Pages: 118

Brand: Triminator Pages: 2

Brand: MAKSIWA Pages: 80

Brand: OEZ Pages: 8

Brand: OEZ Pages: 8

Brand: Siemens Pages: 21

PolyBlend PB200-2

Brand: Siemens Pages: 36

Brand: Siemens Pages: 4

Brand: Siemens Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands