Emerson Liebert APM 120 Manual Download Page 68

Page: 68 / 144

Liebert BDC

™

Liebert

APM

™

6.3

Maintenance Mode

When the Liebert BDC is in Maintenance mode (MBB closed; BIB/MIB open), it provides an alternate

path for power to the connected equipment should the UPS need to be taken out of service for limited

maintenance or repair. In this mode of operation, no power is supplied to the UPS and the load is

NOT protected by the UPS.

6.4

Locating the Cabinet

This Liebert BDC may be mounted to the left of the UPS or installed as a stand-alone unit. In either

case, ensure that the unit is in a well-ventilated area and that there is clearance for access to the

switches and cable connections as required by national and local codes.

6.5

Cable Installation

6.5.1 Wiring Preparation

Be sure that the unit is not connected to any AC utility power source or UPS before installing any

wiring to this unit. This Liebert BDC should be installed by a qualified / certified electrician.

Removing the Cover Plates

Plates cover the input and output terminals on the front of the Liebert BDC (see

Figure 44

). Remove

these and keep the screws and plates for reinstallation.

Figure 44 Liebert BDC—access plate removed

6.5.2 Power Cable Installation

Refer to

Table 43

when selecting cables.

WARNING

Risk of electrical shock and arc flash. Can cause property damage, injury and death.
Read this section thoroughly before attempting to install wiring to this unit. Read and

comply with all warnings and cautions in this manual.

NOTE

Transient and steady state earth leakage currents may occur when starting the equipment.

This should be taken into account when selecting ground current detection devices because

these will carry the earth leakage currents of both the UPS equipment and the load.

Summary of Contents for Liebert APM 120

















































































































































Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands

Emerson Liebert APM 120, Manual

Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands