background image

 

Large screen TVs are heavy. 2 people are required to carry and 
handle a large screen TV.

 

Make sure to hold the upper and bottom
frames of the unit firmly as illustrated.

 

Install the unit in a horizontal and stable
position.

 

Do not install the unit in direct sunlight
or in a place subject to dust or strong
vibration.

 

Depending on the environment, the temperature of this unit may 
increase slightly. This is not a malfunction.

 

Avoid a place with drastic temperature changes.

 

Do not place anything directly on top or bottom of the unit.

 

Depending on your external devices, noise or disturbance of the 
picture and / or sound may be generated if the unit is placed too 
close to them. In this case, please ensure enough space between 
the external devices and the unit.

 

Do not insert the AC power cord into the power socket outlet 
before all the connections are made.

 

Ensure that you always have easy access to the AC power cord or 
plug to disconnect the TV from the power.

 

Before you move the TV, disconnect attached cables to prevent 
damage to connectors.

 

Be sure to unplug the AC power cord from the AC outlet before 
moving or carrying the unit.

Do not place the unit on the furniture that is capable of being tilted 
by a child and an adult leaning, pulling, standing or climbing on it.
A falling unit can cause serious injury or even death.

This apparatus should not be placed in a built-in installation such as a 
bookcase or rack unless proper ventilation is provided.
Make sure to leave a space of 4 inches (10cm) or more around this 
apparatus.

Press    to turn the unit on and go into standby mode.
To completely turn Off the unit, you must unplug the AC power cord.
Disconnect the AC plug to shut the unit off when trouble is found or 
not in use. The AC plug shall remain readily available.

Never use a gas duster on this TV.
The gas trapped inside of this unit may cause ignition and explosion.

CAUTION:

  Danger of explosion if battery is incorrectly replaced. 

Replace only with the same or equivalent type.

WARNING:

  Batteries (battery pack or battery installed) shall not be 

exposed to excessive heat such as sunshine, fire or the 
like.

WARNING:

  To prevent injury, this apparatus must be securely 

attached to the furniture / wall in accordance with the 
instructions. Tipping, shaking, or rocking the unit may 
cause injury / death.

The packaging of this product is intended to be recycled.

Contact your local authorities for information about how to recycle the 
packaging.

For product recycling information, please visit -

www.emersonaudiovideo.com

Emerson pays a lot of attention to produce environment-friendly 
products in green focal areas. Your new TV contains materials which can 
be recycled and reused. At the end of its life, specialized companies can 
dismantle the discarded TV to concentrate the reusable materials and to 
minimize the amount of materials to be disposed of. Please ensure you 
dispose of your old TV according to local regulations.

Disposal of used batteries

The batteries supplied do not contain the heavy metals mercury and 
cadmium. Nevertheless, in many areas batteries may not be disposed 
of with your household waste. Please ensure you dispose of batteries 
according to local regulations.

End of life directives

AC plug

6

English

2 Important

Positioning the TV

Regulatory notices

Environmental care

Summary of Contents for LF320EM5F







































Reviews: