Emerson HVAC Drive H300 Installation And Commissioning Manual Download Page 30

Page: 30 / 40

Electronic Bypass Controller Installation and Commissioning Guide

Section 5 - Programming

5.1 Required Programming

The following parameters must be set to the values shown in order to ensure proper
operation of the electronic bypass package.

The Menu “0” Equivalent parameters

apply to the H300 only.

These settings are pre-programmed from the factory.

DO NOT change any of these values unless directed to by Emerson
technical support. Note these parameters should be programmed in the
sequence shown.

Parameter

Menu 0

Equivalent

Description For H300

Setting

Units

Fan

Pump

01.014

Reference selector

A1.A2 A1.A2

01.051

Power-up keypad reference

LASt (1) LASt (1)

01.052

Enable hand/off/auto keypad

mode

02.006

S ramp enable

On (1)

02.007

Maximum Rate of Change of

Acceleration

s/Max. Hz

06.012

Enable stop key

07.010

00.026

Analog input 1 destination

menu.param

07.014

00.028

Analog input 2 destination

01.036 01.036 menu.param

08.022

Digital I/O 2 source/destination 10.033 10.033 menu.param

08.023

Digital I/O 3 source/destination 06.030 06.030 menu.param

08.024

Digital I 4 destination

01.054 01.054 menu.param

08.025

Digital I 5 destination

01.041 01.041 menu.param

09.004

Logic function 1 source 1

08.003 08.003 menu.param

09.006

Logic function 1 source 2

08.006 08.006 menu.param

09.010

Logic function 1 destination

01.043 01.043 menu.param

Summary of Contents for HVAC Drive H300









































Search results

Summary of Contents for HVAC Drive H300

Reviews:

Related manuals for HVAC Drive H300

Brands by name

Popular brands

Emerson HVAC Drive H300, Installation And Commissioning Manual

Search results

Summary of Contents for HVAC Drive H300

Reviews:

Related manuals for HVAC Drive H300

Brands by name

Popular brands