background image

www.Fisher.com

Fisher

 YD and YS 3‐Way Valves

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

2

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Lubrication

5

. . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Maintenance

6

. . . . . . . . . . . . . . . . . . . . . . . . .

Packing Replacement

6

. . . . . . . . . . . . . . . . . . . . .

Trim Maintenance

7

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assembly

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENVIRO‐SEAL

t

 Bellows Seal Bonnet

16

. . . . . . . . . . .

Replacing a Plain or Extension Bonnet with an

ENVIRO‐SEAL Bellows Seal Bonnet
(Stem/Bellows Assembly)

16

. . . . . . . . . . . . . .

Replacement of an Installed

ENVIRO‐SEAL Bellows Seal Bonnet
(Stem/Bellows Assembly)

18

. . . . . . . . . . . . . .

Purging the ENVIRO‐SEAL 

Bellows Seal Bonnet

19

. . . . . . . . . . . . . . . . . . .

Parts Ordering

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Kits

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gasket Kits

25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

26

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YD and YS Valve

26

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bonnet for YD and YS

26

. . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher YD Valve with 667 Actuator

W2081

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for NPS 1/2 through 8 YD and NPS
1/2 through 6 YS control valves. Refer to separate manuals for instructions covering the actuators and accessories.

Do not install, operate, or maintain YD or YS valves without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. 

To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings.

 If you

have any questions about these instructions, contact your 

Emerson sales office

 or Local Business Partner before

proceeding.

Instruction Manual

D100425X012

YD and YS Valves

July 2017

Summary of Contents for Fisher YD

































Reviews: