Emerson Fisher NPS 8 CHP Instruction Manual Download Page 5

Page: 5 / 14

Instruction Manual

D104197X012

NPS 8 CHP Valve

September 2016

Figure 2. Packing Arrangements

UPPER WIPER (KEY 12)

PACKING FOLLOWER
(KEY 13)

FEMALE ADAPTOR
(KEY 32)

V‐RING (KEY 7)

MALE ADAPTOR
(KEY 31)

WASHER (KEY 10)

SPRING (KEY 8)

PACKING BOX RING
(KEY 11)

LOWER WIPER
(KEY 30)

KEY 6

PACKING FOLLOWER
(KEY 13)

GRAPHITE LAMINATE
PACKING RING (KEY 7)

GRAPHITE FILAMENT
PACKING RING (KEY 9)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

PACKING FOLLOWER
(KEY 13)

PACKING RING
(KEY 7)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

12A8160‐A

14A3412‐B

13A0112‐A

PTFE V‐RING

SINGLE PACKING

GRAPHITE LAMINATE AND FILAMENT

SINGLE PACKING

GRAPHITE/COMPOSITION

DOUBLE PACKING

UPPER WIPER (KEY 12)

PACKING FOLLOWER
(KEY 13)

FEMALE ADAPTOR
(KEY 32)

V‐RING (KEY 7)

MALE ADAPTOR
(KEY 31)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

LOWER WIPER
(KEY 30)

KEY 6

PACKING FOLLOWER
(KEY 13)

GRAPHITE LAMINATE
PACKING RING (KEY 7)

GRAPHITE FILAMENT
PACKING RING (KEY 9)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

PACKING FOLLOWER
(KEY 13)

PACKING RING
(KEY 7)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

12A7839‐A
Sht 1

14A3414‐B

12A8163‐A

PTFE V‐RING

DOUBLE PACKING

GRAPHITE LAMINATE AND FILAMENT

DOUBLE PACKING

PTFE/COMPOSITION

DOUBLE PACKING

PACKING ARRANGEMENTS FOR 31.8 mm (1‐1/4 INCH) VALVE STEMS

NOTES:
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS.
USE ONLY ONE BELOW EACH GRAPHITE LAMINATE RING.

HAS THE APPEARANCE OF FLAT WASHERS PRESSED TOGETHER.
HAS THE APPEARANCE OF A WOVEN OR BRAIDED RING.

C0634‐1

Summary of Contents for Fisher NPS 8 CHP















Search results

Summary of Contents for Fisher NPS 8 CHP

Reviews:

Related manuals for Fisher NPS 8 CHP

Brands by name

Popular brands

Emerson Fisher NPS 8 CHP, Instruction Manual

Search results

Summary of Contents for Fisher NPS 8 CHP

Reviews:

Related manuals for Fisher NPS 8 CHP

Brands by name

Popular brands