manualshive.com logo in svg

Emerson Fisher HP, Instruction Manual

Share
Download
Emerson Fisher HP Instruction Manual Download Page 4

Instruction Manual

D104480X012

HP Control Valve Startup Trim

July 2019

4

Figure 3. Installation of Cage with Hoist Rod and Nut

GH02761

VALVE BODY (1)

HOIST NUT

HOIST ROD

CAGE (2)

BACK-UP RING (9)

BORE SEAL (42)

3.  Install the cage (key 2) into the valve body. When installing the cage (key 2), take care to lower the cage evenly and

ensure that cage (key 2) will not damage the flat sheet gasket (key 12) during installation. See figures 4 and 5.

Figure 4. Install Cage to Seat on the Flat Sheet Gasket

GASKET (12)

CAGE (2)

VALVE BODY (1)

4.  Install three-cage spiral wound gasket (key 43) in the gasket groove on top of the cage (key 2), making sure the

gaskets sit flush on the surface of the groove. See figure 5.

5.  Install the bonnet spiral wound gasket (key 11) in the gasket groove on top of the body (key 1), making sure the

gasket sits flush on the surface of the groove.

6.  Threaded surfaces of the studs (key 13), faces of the nuts (key 14), washers (key 40) and nut seating surface on the

bonnet (key 18) should be lubricated with nickel-based anti-seize lubricant prior to assembly.

Note

Take care not to introduce lubricant between the washer and the bonnet surface.

Summary of Contents for Fisher HP













Reviews:

No comments

Brands by name

Popular brands

Load more brands