background image

www.Fisher.com

Fisher

 HP Control Valve Startup Trim

for NPS 8 and Larger

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

2

. . . . . . . . . . . . . . . . . . . . . . . . .

Valve Installation

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trim Removal

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation of Startup Trim Kits

3

. . . . . . . . . . . . . . . . . .

Flushing and Hydro Trim Kit

3

. . . . . . . . . . . . . . . . . . .

Chemical Cleaning Trim Kit

8

. . . . . . . . . . . . . . . . . . . .

Disassembly of Startup Trim Kits

9

. . . . . . . . . . . . . . . .

Flushing and Hydro Trim Kit

9

. . . . . . . . . . . . . . . . . . .

Chemical Cleaning Trim Kit

9

. . . . . . . . . . . . . . . . . . . .

Cleaning

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trim Replacement and Valve Reassembly

10

. . . . . . . .

Parts Ordering

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher HP Control Valve with 585C Actuator
and FIELDVUE

 DVC6200 Digital Valve Controller

X1597

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for the Fisher HP Control Valve
Startup Trim for NPS 8 and larger.

Do not install, operate, or maintain HP valves without being fully trained and qualified in valve, actuator, and accessory
installation, operation, and maintenance. 

To avoid personal injury or property damage, it is important to carefully

read, understand, and follow all the contents of this manual, including all safety cautions and warnings.

 If you have any

questions about these instructions, contact your 

Emerson sales office

 before proceeding.

Instruction Manual

D104480X012

HP Control Valve Startup Trim

July 2019

Summary of Contents for Fisher HP













Reviews: