manualshive.com logo in svg

Emerson Fisher EHD, Instruction Manual

Share
Download
Emerson Fisher EHD Instruction Manual Download Page 10

Instruction Manual

D100394X012

EH (1-1/2x1 through 8x6)

July 2017

10

Figure 4. Packing Arrangements

UPPER WIPER (KEY 12)

PTFE V‐RING

SINGLE PACKING

GRAPHITE RIBBON AND FILAMENT

SINGLE PACKING

12A8160‐A

PACKING FOLLOWER
(KEY 13)

FEMALE ADAPTOR
(KEY 32)

V‐RING (KEY 7)

MALE ADAPTOR
(KEY 31)

WASHER (KEY 10)

SPRING (KEY 8)

PACKING BOX RING
(KEY 11)

LOWER WIPER
(KEY 30)

PACKING FOLLOWER
(KEY 13)

PACKING BOX RING
(KEY 11)

GRAPHITE RIBBON
PACKING RING (KEY 7)

GRAPHITE FILAMENT
PACKING RING (KEY 7)

LANTERN RING
(KEY 8)

KEY 6

14A3412‐C

1

2

3

1

1

PACKING FOLLOWER
(KEY 13)

PACKING BOX RING
(KEY 11)

GRAPHITE RIBBON
PACKING RING (KEY 7)

GRAPHITE FILAMENT
PACKING RING (KEY 7)

LANTERN RING
(KEY 8)

2

UPPER WIPER (KEY 12)

PACKING FOLLOWER
(KEY 13)

V‐RING (KEY 7)

MALE ADAPTOR
(KEY 31)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

LOWER WIPER
(KEY 30)

KEY 6

3

FEMALE ADAPTOR
(KEY 32)

UPPER WIPER (KEY 12)

PACKING FOLLOWER
(KEY 13)

LANTERN RING
(KEY 8)

PACKING BOX RING
(KEY 11)

PACKING RING
(KEY 7)

PTFE V‐RING

DOUBLE PACKING

GRAPHITE RIBBON AND FILAMENT

DOUBLE PACKING

PTFE/COMPOSITION

DOUBLE PACKING

12A7839‐A
Sht 1

14A3414‐C

12A8163‐A

NOTES:
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS.
USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.

HAS THE APPEARANCE OF A WOVEN OR BRAIDED RING.
INCLUDED IN KEY 6 PACKING SET.

1

2

3

C0637‐1

CAUTION

All residual gasket material must be removed from the cage gasket surfaces. If the gasket surfaces are scored or damaged
during this process, smooth them by hand sanding with 360 grit paper using long, sweeping strokes. Failure to remove all
residual gasket material and/or burrs from the gasket surfaces will result in leakage.

6.  Clean all gasket surfaces with a good quality degreaser. Remove all residual tin or silver from all gasket surfaces.
7.  Cover the opening in the valve body to protect the gasket surface and to prevent foreign material from getting into

the valve body cavity.

8.  Remove the packing flange nuts (key 5), packing flange (key 3), upper wiper (key 12), and packing follower (key 13,

figures 4 and 16). Carefully push out all the remaining packing parts from the valve side of the bonnet using a

Summary of Contents for Fisher EHD





































Reviews:

No comments

Brands by name

Popular brands

Load more brands