background image

www.Fisher.com

Fisher

 8540 Eccentric Disk 

Butterfly Control Valve

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve Orientation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Maintenance

9

. . . . . . . . . . . . . . . . . . . . . . . . .

Seal Ring Maintenance

11

. . . . . . . . . . . . . . . . . . . . . .

Disk, Drive Shaft and Bearing Maintenance

15

. . . . . .

Actuator Mounting

18

. . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher 8540 Butterfly Valve with Bettis RPE
Actuator and 3720 Positioner

X1846

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for the 8540 Eccentric Disk Butterfly
Control Valve (see figure 1). Refer to separate instruction manuals for information covering the actuator and
accessories.

Do not install, operate, or maintain 8540 valves without being fully trained and qualified in valve,
actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property
damage, it is important to carefully read, understand, and follow all the contents of this manual,
including all safety cautions and warnings. If you have any questions about these instructions, contact
your 

Emerson sales office

 before proceeding.

Description

The seal design of the 8540 eccentric disk high performance butterfly valve provides excellent shutoff capability. This
valve has a square drive shaft end and soft seal rings for use in a wide variety of applications.

Instruction Manual

D104709X012

8540 Valve

September 2021

Summary of Contents for Fisher 8540

























Reviews: