background image

- 10 -

EN

9J27

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the
arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the
polarity (+/-) markings.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or
video camera), connect the player’s audio/video out-
put cables to the AUDIO IN/ VIDEO IN jacks of
your TV/VCR. Then press the CHANNEL

K

or 

L

button until “AUX” appears on the screen.

AUX

TO RECORD A SCRAMBLED/UNSCRAMBLED
CHANNEL

1. Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

MOBILE CONNECTION

1) The supplied indoor antenna is adequate when

your vehicle is stationary. For best reception on
the road, use a high-quality VHF/UHF mobile TV
antenna.

2) Attach the car battery cord to the DC13.2V(12V)

connector on the back of the TV/VCR. Then, con-
nect the other end to your vehicle’s cigarette-
lighter socket.

NOTES:

Be sure your vehicle has a 13.2-volt (12-volt), neg-
ative-ground electrical system.

Be sure you use only the supplied car battery cord.
Using another cord could damage the TV/VCR.

Be sure the socket is free of ashes and other debris.

Be sure to push the car battery cord’s plug com-
pletely into the cigarette-lighter socket.

Always unplug the car battery from the cigarette-
lighter socket before you unplug it from the
TV/VCR.

You must disconnect the car battery cord from the
TV/VCR before you can use the AC power.

Be sure to replace the fuse with only the same
type, 5A, 250V.

WARNING: The driver should never watch
the TV/VCR while operating a motor vehicle.

CAUTION: If you use the TV/VCR with the
vehicle’s engine off, recharge the vehicle’s
battery after about every 4 hours of use to
prevent it from running down. After you fin-
ish using the TV/VCR be sure you unplug the
car-battery cord from the cigarette-lighter
socket.

ANT.

DC13.2V

DC13.2V

AC  120V

CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX

If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in drawing.
By using this connection you can also record scram-
bled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR Remote Control. Unattended timer record-
ing is limited to one channel at a time.

VHF/UHF Combination 
Mobile Antenna
(Not supplied)

To the vehicle's
cigarette-lighter socket

Car battery cord
(Supplied)

Summary of Contents for EWC0902

































Reviews: