Emerson ET124 Series Instruction Manual Download Page 8

VCIMD-16109 © 2021 Emerson Electric Co. All rights reserved. 11/21  

Spence is a mark owned by one of the companies in the Emerson Automation 

Solutions business unit of Emerson Electric Co. The Emerson logo is a 

trademark and service mark of Emerson Electric Co. All other marks are 

property of their prospective owners.
The contents of this publication are presented for informational purposes only, 

and while every effort has been made to ensure their accuracy, they are not to 

be construed as warranties or guarantees, express or implied, regarding the 

products or services described herein or their use or applicability. All sales are 

governed by our terms and conditions, which are available upon request. We 

reserve the right to modify or improve the designs or specifications of such 

products at any time without notice.
Emerson Electric Co. does not assume responsibility for the selection, use 

or maintenance of any product. Responsibility for proper selection, use 

and maintenance of any Emerson Electric Co. product remains solely with 

the purchaser.

Parts Ordering

When corresponding with your local Sales Office 

about this equipment, always reference the equipment 

regulator size, service and serial number.
When ordering replacement parts, reference the key 

number of each needed part as found in the following 

parts list and indicate the part number. 

Parts List

Type E Main Valve

See Instruction Manual VCIMD-14961-EN

Type E2 Main Valve

See Instruction Manual VCIMD-14935-EN

T124 and T134 Series Pilot

See Instruction Manual VCIMD-14980-EN

ET124 and ET134 Series 

Emerson Automation Solutions

Americas 

McKinney, Texas 75070 USA 

T   +1 800 558 5853 

+1 972 548 3574

Europe 

Bologna 40013, Italy 

T  +39 051 419 0611

Asia Pacific

 

Singapore 128461, Singapore 

T  +65 6777 8211

Middle East and Africa 

Dubai, United Arab Emirates 

T  +971 4 811 8100

SpenceValve.com

SIOI85B

Summary of Contents for ET124 Series









Reviews: