Emerson Bettis M18 Installation, Operation And Maintenance Manual Download

Page: 3 / 32

Installation, Operation and Maintenance Manual

VA-DC-000-1879 Rev. 0

Table of Contents

April 2021

Table of Contents

Table of Contents

Section 1: Introduction

1.1

General M18 Service Information .................................................................. 1

1.2

Definitions .................................................................................................... 2

1.3

General Safety Information ........................................................................... 2

1.4

Fluid Requirements ....................................................................................... 3

1.5

Bettis Reference Materials ............................................................................. 3

Section 2: General Information

2.1

Actuator Power Operation ............................................................................. 4

2.2

Actuator M18 Manual Hydraulic Operation ................................................... 4

Section 3: M18 System Fluid Filling Instructions

3.1

Double-Acting Actuator M18 System Fluid Filling .......................................... 5

3.2

Spring-Return Actuators M18 System Fluid Filling ......................................... 8

3.3

Priming M18 in the Field.............................................................................. 11

Section 4: M18 Disassembly Instructions

4.1

M18 Pressure Release Instructions .............................................................. 12

4.2

M18 Reservoir Disassembly Instructions...................................................... 12

4.3

M18 Pump Disassembly Instructions ........................................................... 13

Section 5: M18 Reassembly Instructions

5.1

M18 General Reassembly Instructions ......................................................... 16

5.2

M18 Reservoir Reassemble Instructions ...................................................... 16

5.3

M18 Pump Reassembly Instructions ............................................................ 17

Appendix A: List of Drawings

A.1

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 1 of 7 ................. 20

A.2

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 2 of 7 ................. 21

A.3

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 3 of 7 ................. 22

A.4

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 4 of 7 ................. 23

A.5

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 5 of 7 ................. 24

A.6

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 6 of 7 ................. 25

A.7

Part No. VA-ED-005-1120, M18 Assembly Drawing, Sheet 7 of 7 ................. 26

Summary of Contents for Bettis M18

































Search results

Summary of Contents for Bettis M18

Reviews:

Related manuals for Bettis M18

Brands by name

Popular brands

Emerson Bettis M18, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Bettis M18

Reviews:

Related manuals for Bettis M18

Brands by name

Popular brands