Emerson 1410S Quick Start Manual Download Page 7 | Manualshive

Page: 7 / 44

background image

3

Initial connection and configuration

To configure the gateway, a local connection between a computer and the
gateway needs to be established.

Powering the Gateway

For the Emerson Wireless 1410S Gateway, bench top power will be needed
to power the Gateway by wiring a 10.5–30 VDC power source.

An Emerson Wireless 1410S Gateway can also be powered via Power over
Ethernet (PoE) and is compliant with the IEEE 802.3af standard.

Note

The Emerson Wireless 1410S2 Gateway hardware revision 1.0.0 configured
with Intrinsically Safe Outputs option “A” can only be powered by 24 VDC
power source. Check label to verify hardware revision.

July 2022

Quick Start Guide

Quick Start Guide

7

«
...
5
6
7
8
9
...
»

Summary of Contents for 1410S













































Reviews:

No comments

Related manuals for 1410S

Brand: Karel Pages: 17

Brand: AMPLIFIED ENGINEERING Pages: 20

Brand: Nortel Pages: 111

Intesis Modbus Server

Brand: HMS Pages: 30

Brand: OleumTech Pages: 104

Brand: ZyXEL Communications Pages: 2

Brand: Berker Pages: 4

Brand: Fastus Pages: 2

Brand: Soyal Pages: 4

Brand: Carotron Pages: 20

hotspot gateway

Brand: Jaze Pages: 102

Brand: VoiceInterop Pages: 16

Brand: Orchid Telecom Pages: 3

Brand: NETGEAR Pages: 59

ShareLink Pro 500

Brand: Extron electronics Pages: 59

Brand: Netronix Pages: 43

Brand: Laird Pages: 39

Brand: Panasonic Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands