manualshive.com logo in svg

EMC2 40U-C, Unpacking And Setup Manual

Share
Download
EMC2 40U-C Unpacking And Setup Manual Download Page 2

Before you start

This section contains important information you should read prior to unpacking and
setting up the cabinet.

CAUTION

Some EMC

®

 products are designed for installation by trained service personnel only.

Attempts by unqualified personnel to set up and start certain products may result in
system damage and may void product warranties. Contact your EMC representative for
detailed warranty, installation, and initialization policies.

Please dispose of shipping material responsibly, and recycle wherever and whenever
possible. Cabinet packaging that includes a collapsible downloading ramp can be re-
packaged and returned, as described in 

Repackaging shipping material (2-piece ramp

kits only) on page 12

.

CL5427

Note

The illustrations in this guide are examples only. Depending on what you ordered, your
configuration may look somewhat different from what is shown here.

Tools required

l

9/16-in. (14-mm) socket wrench

l

Adjustable wrench

l

Flat screwdriver

l

Phillips screwdriver

2

40U-C Cabinet

  

Summary of Contents for 40U-C

















Reviews:

No comments

Brands by name

Popular brands

Load more brands