EMC VNX5300 Block Hardware Information Manual Download Page 76 | Manualshive

Page: 76 / 88

background image

EMC® VNX5300™ Hardware Information Guide

76

EMC® VNX5300™ Hardware Information Guide

VNX5300 DAE cabling

IMPORTANT

!

The DAE(s) that are to be directly connected to the DPE need to be located close
enough to the DPE so that the DPE-to-DAE interconnect cables (that are provided
with every DAE) can be routed and connected to the DPE.

Shown in the upcoming figures (

Figure 71 on page 77

Figure 72 on page 79

graphical representations of SAS cabling in a DPE-based VNX storage platform, the
VNX5300 Block. The Storage Processors connect to the DAEs with SAS cables. The
cables connect LCCs in the DAEs of a storage platform together in a daisy-chain
topology.

The DPE is automatically Enclosure 0 (EA0). The DAE connected to SAS output port
0 is Enclosure 1 (EA1).

Cabling with two
DAEs in VNX5300
Block platform

The first DAE connected to the Storage Processor SAS output port 1 is designated
Enclosure 0 (EA0). Each DAE connected after the first DAE increments the enclosure
number by one. All enclosures connected to SAS Port 0 will be on ID 0, but the
addresses will increment.

Figure 71 on page 77

shows the first example of a VNX5300 Block platform with two

DAEs (one 3U, 15 disk drive DAE and the other a 2U, 25 disk drive DAE) or a
VNX5300 platform with a total of from 55 disk drives (if the DPE is a 3U, 15 disk
drive device) or 65 disk drives (if the DPE is a 3U, 25 disk drive device).

The SAS ports on the VNX5300 platform DPE are labeled 0 and 1. SAS 0 is connected
internally to the SAS expander that connects the internal DPE disks. Since SAS 0 is
already connected internally to the DPE disks, the first DAE is connected to SAS 1 to
balance the load on the SAS ports. The second DAE is connected to SAS 0, the third
DAE is connected to SAS 1, and so on.

In

Figure 71 on page 77

, notice that each DAE device supports two completely

redundant buses (LCC A and LCC B).

The rule of load or bus balancing is applied to all DAEs. That is, Bus 0 is Enclosure
Address 0 (EA0), Bus 1 is EA0, and so on. In the case of the VNX5300 platform, Bus 0
EA0 is the DPE (SP A and B). So, to balance the load, Bus 1 EA0 becomes the first
DAE (LCC A and B) in the cabinet with the next DAE (LCC A and LCC B) as Bus 0
EA1, and so on. If you have several DAEs in your VNX5300 platform, you can daisy
chain them within that particular bus. However, it is recommended that you balance
each bus. In other words, always optimize your environment by using every
available bus, and spreading the number of enclosures as evenly as possible across
the buses.

Note:

On the DPE and DAE, each cable connector includes a symbol to denote the direction the

cable needs to connect to. The cable connector that has a double circle symbol is the input to the
device. The cable connector with the double diamond symbol is the output from the device.

IMPORTANT

!

Notice the description of the cable labels affixed to the SP to DAE cables.

«
...
74
75
76
77
78
...
»

Summary of Contents for VNX5300 Block

























































































Reviews:

No comments

Related manuals for VNX5300 Block

Brand: Wave wifi Pages: 2

Brand: NavigateWorx Pages: 71

Brand: Conceptronic Pages: 230

Asynchronous SH7145F

Brand: Renesas Pages: 17

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

HomePlug AV Ethernet Bridge PLE0200

Brand: Abocom Pages: 2

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Brand: ZALMAN Pages: 9

Brand: B&B Electronics Pages: 2

Brand: Paradyne Pages: 6

Brand: SeaLevel Pages: 34

Brand: Hauppauge Pages: 55

Brand: 2N Telekomunikace Pages: 67

Brand: Keil Pages: 68

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: Datalogic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands