background image

Tinyhawk II

13

emax-usa.com

Arming

Arming refers to setting Tinyhawk II to a fly ready state. When Tinyhawk II is

powered on first it will not spin up the propellers until it is armed. Arm the aircraft by

first moving throttle to the bottom position. Then move the left switch of the radio to

its 3

rd

position upwards. You will see the propellers spinning when Tinyhawk II is

successfully armed.

In the event of a crash always disarm immediately. Failure to disarm in a timely

manner can damage Tinyhawk II.
Always disarm Tinyhawk II before handling it.

Flying Modes

Tinyhawk II comes stock set in rate mode. This is an advance mode where control

sets the angular rate of the aircraft. The AUX 2 switch is set to change this mode on

a 3 stage switch. When AUX 2 is in a high state, Tinyhawk II will be in angle mode

where control sets the attitude of the aircraft. When the switch is in the middle state,

Tinyhawk II will be in Horizon mode.

Line of Sight Flying

To learn how to fly Tinyhawk II start by flying it line of sight (no goggles yet). Power

on Tinyhawk II and set it down in a cleared room. Arm Tinyhawk II then throttle up

using the left stick to a hover position. Work on maintaining a constant altitude. Pitch

and roll Tinyhawk II with the right thumb stick and yaw Tinyhawk II with the left thumb

stick.

First Person View (FPV) Flying

Make sure Tinyhawk II and the goggles are on the same vtx channel and that you

have a clear area to fly around in. Apply the same principals learned when flying

Tinyhawk II line of sight except now work on flying in a forward direction while

maintaining a controlled constant altitude. It is easier to learn flying FPV by always

moving in a forward direction so always apply a slight amount of pitch using your

right thumb stick. You can steer Tinyhawk II like a car using yaw on the left thumb

stick.
There is an on screen display (OSD) overlaying the video feed from the camera of

Tinyhawk II. The OSD displays important information such as flight time and battery

voltage. Pay attention to these numbers during flight to know how much battery life is

Summary of Contents for Tinyhawk II


















Reviews: