2
3
1
4
5
6
7
9
10
11
12
14
16
15
13
17
18
19
20
22
21
24
25
26
23
27
8
2-4
MAIN DIMENSION
REPLACEMENT PARTS OF FILTER
3-4
3 Replace filter coping. Put the twelve nuts and washers onto each of the twelve bolts, then screw all the nuts
on with wrench,ensuring that all nuts are tight.
a
4 Connect pump to control valve opening marked PUMP.
5 Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
6 Make electrical connections to pump per pump instructions.
7 To prevent water leakage, be sure all pipe connections are tight.
)
) Carefully screw pressure gauge (with O'ring in place) into tapped hole in the filter coping. Do not over-
tighten.
b) Ensure air relief valve (with O'ring in place) is tight fit to filter coping and turn it easily.
)
)
)
)
B
A
820
920
Model
A
High
mm
B
Diameter
mm
1050
1180
S800
S900
723
890
S700(B)
REPLACEMENT PARTS OF MULTIPORT VALVE
Valve Port
Size
Inch
Sand
Kg
2”
2”
2”
355
470
215
Key
No.
Part
No.
Product
Description
Qty
1
01013003
Handle
(
Big
)
1
2
03018008
Pin
for
Handle
1
3
01181027
Washer
for
Handle
1
4
01051026
2
.
0" Side
Mount
Valve
Squareness
Lid
(
White
)
1
5
89280301
M6
*
32
Screw
with
Nut
10
6
01111048
Connector
for
Pressure
Gauge
/
Stopper
1
02011139
O
-
Ring
1
7
89021303
Drain
Plug
with
O
'
Ring
1
8
06011029
Oil
Pressure
Gauge
With
O
-
ring
(
40psi
)
1
9
02020016
O
-
Ring
for
2
.
0
"
Union
8
10
01051033
2
.
0" Connector
(
White
)
3
11
01171154
2
.
0" Union
(
A
/
E
)
3
12
01051032
2
.
0" Union
Nut
(
White
)
3
13
02011009
O
-
Ring
for
2
.
0" Valve
Lid
1
14
01181002
Washer
for
spring
1
15
02011022
O
-
Ring
for
2
.
0" Valve
Rotor
2
16
03014014
Spring
1
17
01021002
2
.
0" Valve
Rotor
1
18
02311003
Spider
Gasket
1
19
01051027
2
.
0" Side
Mount
Valve
Bottom
Body
(
White
)
1
20
89280104
Sight
Glass
With
O
-
Ring
1
21
02011011
O
-
Ring
for
Union
Tale
1
22
01051035
2
.
0" Union
Tale
(
White
)
1
23
01013034
2
.
0" Union
Nut
(
Black
)
2
24
02020017
O
-
Ring
for
Plug
1
25
01051029
2
.
0" Side
Mount
Valve
Plug
(
White
)
2
26
01051195
2
.
0" Elbow
Tube
(
White
)
183mm
1
27
01171035
2
.
0" Union
Adaptor
(
Metric
)
1
DIMENSION
TABLE
INSTALL/START-UP OF FILTER
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are
secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve
seal, always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open),
allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at
least 1 minute. The initial back-washing of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear,
about 1/2 to 1 minute.Turn pump off and set valve to FILTER position and restart pump.The filter is now
operating in the normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending
upon the pump and general piping system.) As the filter removes dirt and impurities from the pool water,
the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge
reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see
BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
Key
No.
Part No.
Description
Qty
1
89010601
Nut with washer
12
2
89010701
Air Release Valve with Oring
1
3
06011032
Maximum 40PSI Indication, Stainless Steel Casing
1
4
01172005
Lid (Grey Colour)
1
5
02011126
Filter Neck Gasket
1
6
89011202
S700B Filter Tank
1
6
89011208
Filter Tank with Base for S800
1
6
89011209
Filter Tank with Base for S900
1
7
89011203
The Inner Tank System for S700 (B)
1
7
89011210
The Inner Tank System for S800
1
7
89011211
The Inner Tank System for S900
1
8
01111090
2.0" Tank System Support
1
9
02011127
O-Ring for Inlet & Outlet
2
10
88280813W
6 Way 2" Valve with Piping Kit, 2" union set x 3 and
pressure gauge (White)
1
11
01172010
Laterals (185mm)
8
11
01172011
Laterals (233mm)
8
12
89010107
Water Drain Set
1
13
01111062
21-28inch Filter Base
1
13
01112038
32-40 inch Filter Base
1
Notes:11* 01172010 laterals (185mm) is for S700B
11* 01172011 laterals (233mm) is for S800 & S900
